Gypsum glue for tiles: features of use, types and reviews

Gypsum today becomes the basis for many building materials. It can be glue or products in the form of a tile. About them and will be discussed in the article. The information presented below will allow you to understand what types of gypsum glue today exist, and also what composition for laying gypsum tile is better to use. It is important before starting the work to find out more about what technology is necessary to operate.

Varieties of gypsum glue

Gypsum glue for tiles is usually available in the form of a dry powder. This kind of mixture is the most successful. To increase the adhesion to the ingredients, special substances are added, in addition, they allow you to work with the glue without hurrying. If you are wondering about what to glue gypsum tile, it is worth paying attention to another kind of such families, which requires the use of sand quartz. It is added for cheaper production. In expensive glues this ingredient is either small, or not at all. Depending on the volume of additives, the characteristics can vary.

As the main task of the adhesive is a strong adhesion to the surface. Another variety of the composition described has an increased volume of gypsum. This also affects the adhesion. This quality is also determined by the volume of water that is used to dilute the powder. The amount of liquid is usually indicated on the package. If you learned from the instructions that per 1 kg of glue 300 ml of water is needed, then it can be argued that there is not enough gypsum in such a composition, while there are a lot of fillers. From this it follows that this type of glue will have reduced adhesive capacity. In this case, the glued material can peel off during operation.

Features of choice

When choosing an adhesive, remember the ratio of water and gypsum. A fairly important indicator is the timing of setting the mixture. If the glue is good, then this period should be less. Depending on this indicator, you determine the rate of work that you need to adhere to for gluing the material.

Gypsum tile adhesive usually retains its ability after dilution for an hour. This does not mean that after applying to different materials, the preservation time of the mixture will remain the same. Each manufacturer has this indicator. As practice shows, the minimum period is 30 minutes, while the maximum is 70 minutes.

Reviews about gypsum glues from different manufacturers

If you need gypsum glue for tiles, then you can prefer "Volma montage", which basically contains astringent gypsum, chemical impurities and modified additives. In the role of the main advantages of this mixture, consumers note the water-retaining characteristics and optimal working time. That is why this mixture is chosen by consumers quite often.

It can be used at temperatures ranging from +5 to +30 ° C. At the same time, the optimum humidity should be maintained. Buyers like that the adhesive adheres well with plaster, concrete, gypsum products, aerated concrete and foam block, brickwork, gypsum fiber sheets and plasterboard.

According to customers, Knauf-Perlix glue is also quite popular. It is realized in the form of a powder, and in the role of the main binding components in this case there are additional elements and an astringent gypsum. Buyers emphasize that this composition can be used for internal works.

Features of use of "Knauf-perlfix"

If you decide to purchase the above-described gypsum glue for tiles, you should familiarize yourself with the features of its use. Before starting the work, the base is prepared, for this purpose it is cleaned of impurities and the protrusions are removed from the surface. If the walls absorb moisture well, with regard to aerated concrete, silicate, ceramic elements and plaster, the surface must first be treated with a primer, "Concrete contact" can be used.

These procedures can improve the adhesion of the surface. The base should be left to dry, only after you can proceed to further work. It is important to observe the cleanliness of the primed surface.

Preparation of gypsum glue

To mix the powder with water it is necessary to use a plastic container in which pure water is poured. To the liquid should gradually add glue, mixing the compound with a construction mixer. In the end, you should get a creamy consistency without lumps. It is not recommended to add other components to the solution. It is important to take care that the mixing container is clean.

Technology of glue use

After you figured out which adhesive for gypsum tiles to use, you can start work. The composition is applied to the wall, and then to the surface of the tile. Products will need to be pressed against the surface and set the level by tapping. If the base has grooves more than 2 cm, then they must be closed with plasterboard, using the same adhesive.

When gluing the insulation material, it must be wiped with a Knauf-Perlix solution. After completion of the work, the tools are washed under running water. Before going to the store, you must calculate how much mixture you need. When addressing this issue, follow the manufacturer's recommendations. Of these you can find out that one square meter of surface will need about 5 kg of dry powder.

Is it possible to lay tiles on plaster of plaster

Quite often, home-based masters are wondering whether it is possible to glue tiles on gypsum plaster. The answer is positive, but the foundation must first be prepared. This is due to the fact that the surface needs to give quality enhanced adhesion and strength, reduce the culvert ability of the material and only after you start laying the tile.

It is also important to take care of the alignment of defects. For the reason that for laying should be used not too thick layer of glue, chipped and potholes should be smeared with plaster. Work with such a surface can be after completely drying it. It is recommended that the walls be treated with an antifungal compound.

Do not lay the tile if the plaster coat has not been primed. This stage is the most important for achieving a positive result. If you also faced the question of whether you can glue the tiles on gypsum plaster or not, then you should first become familiar with the functions of the primer. It is able not only to reduce the porosity of the material, but also to increase the safety margin of the coating. The primer will prevent the penetration of moisture inside and will positively affect the quality of the clutch.

Adhesive for gypsum tiles

In the modern variety of building materials can be lost. However, the recommendations presented below will allow you to understand which composition is best used for gypsum tiles. Powdered mixture based on quartz sand and gray cement is PLUSFIX glue. Among its ingredients, there is also cellulose. This mixture is suitable for small tiles. The work can be carried out on the following surface types:

• Brick;
• Cement;
• Concrete.

Very similar to the characteristics of the adhesive described above and the composition called LITOKOL K 17. The latter consists of quartz sand and Portland cement, the first of which is presented in a granular form. This mixture is used for gluing large format tiles. A mixture of mineral aggregates, gypsum and high quality additives is the glue Satyn PKG-28. The ingredients give the composition a high plasticity.

After cooking, the mixture will remain viable for 50 minutes. Another composition on a gypsum base is Gipsolit. It quickly sets, and the remnants can be removed from the surface with a sponge, previously soaked in water. If you can not find the glue for gypsum tiles for a brick, then you should pay attention to the material "Monte Alba". It is used exclusively for interior work and is ideal for gypsum facing.

The process of laying gypsum tiles

Before starting work, you need to figure out how to glue the gypsum tiles on the wall. On the surface you need to apply a little glue a thin layer, the product is then pressed against the wall, within a few minutes it will be possible to correct its position. To smooth the joints, plastic spacers can be used.

The mortar protruding from the seams should be immediately removed with a rubber spatula. Otherwise, it will not be possible to work with the composition. Before starting repairs, be sure to figure out how to glue the plaster tiles on the wall, tips on this are presented in the article. For example, do not dilute too much solution, because if you do not have experience, it will quickly solidify, which will cause unnecessary costs.