Alkaline batteries: operation features

For the maintenance of vehicles used batteries (acid and alkaline). However, the rules for operating devices differ. If we consider alkaline models, then they have a lot of advantages, so they are in demand. First of all, it's important to mention a wide range of operating temperature. Cases of instantaneous failure in models are excluded. At minus temperature they can be stored for a long time without any risk. The alkaline battery is quite simple.

The main elements are nickel electrodes. Also, models use current leads of different thicknesses. All models in the body are filled with electrolyte. In terms of density, it can differ. In order to understand the devices in more detail, it is necessary to familiarize yourself with the general rules for the operation of storage batteries, as well as specific modifications.

General Terms of Use

All the batteries are connected by the method of trimming. To do this, the contacts are supplied with a voltage of different power. You should also know a few rules for pouring electrolyte. The whole process is carried out through the neck, which is located in the upper part of the body. However, before that it is important to check the plastic tank.

When dirt is detected, it should be removed. At the same time, you can handle rust with kerosene. Some modifications are very sensitive to sudden changes in temperature. It is also important to consider that the nuts of the device should be tightened periodically. When storing batteries for a long time, it is necessary to change the electrolyte from the tank. Depending on the capacity of the model, the device needs to be given some time to infuse. Charging must be done until the end.

Models of "Optima"

These alkaline batteries for cars are made with nickel electrodes. In this case, the current lead is located in the lower part of the housing. If necessary, check the electrolyte level very simply. In order to use the device, you need to do the trimming. To operate the model, the top contacts are checked first.

To sharp changes in temperature they are not too sensitive. However, dirt can greatly interfere with the normal operation of the battery. To avoid device failure, wipe the contacts with a dry cloth. If the body shows darkening, then you need to use kerosene. In some cases, experts recommend changing the electrolyte.

Accumulators "Garden"

Before using these batteries, it is important to check the electrolyte level. If the model has been stored for a long time at a negative temperature, weld seams should be checked. Also, many experts recommend periodically tighten the nuts. Large temperature drops, these alkaline batteries are not afraid. Before connecting the device, check the rated voltage. After changing the electrolyte, you do not need to charge the device. It is also important to note that dust should always be removed from the contacts. Sometimes salt may settle on them.

Using SBS batteries

These alkaline batteries (1.2 volts) are very sensitive to mechanical damage. In this case, the nickel electrodes are located next to the separators. Sometimes plastic between them can stick. In this situation, you should immediately replace the electrolyte. However, first of all, the voltage of the device is checked. On average, this parameter should be 2 V. After changing the electrolyte, do not immediately charge. Minimum should wait two hours. After that, the trimming is done. At this stage, it is important to check the tightness of the connections. You also need to pay attention to contacts.

When you find salt, you need to use a rag. After the rastering, the rated voltage of the batteries should be checked again. If this figure does not exceed 2 V, the devices can not be operated. Many experts recommend charging them with a weak current. In this case, the capacity decrease occurs quickly. In some cases, the batteries come into disrepair from the broken current lead. Then you should contact the service center. You can charge this model from any source.

Data Safe Models

These alkaline batteries are equipped with a durable bolted boron. It is also important to note that the device uses lamellar type electrodes. Pour electrolytes can only be carried out through the neck. Rasterization is carried out with a charge of up to 2 V. In this case, the reduction in capacity is very dramatic. In some cases, experts advise to drain the electrolyte in advance. After that, the tank should stand for about two hours.

It is also important to monitor the dryness of contacts. However, rust on them appears rarely. Separate attention should be given to compounds. In some cases, the bolts must be tightened tightly. After charging the electrolyte, it is allowed to charge the batteries after three hours. Connect the devices directly through the negative pole. The initial voltage of this battery should not exceed 1.4 V.

Operation of alkaline batteries of the "NK-28" series

These alkaline batteries are manufactured in a plastic housing. As experts say, they are not afraid of mechanical damage. However, one should beware of negative temperatures. You can charge the device from any source. With long-term storage of batteries, you can immediately change the electrolyte. In this case, the electrodes are of the lamellar type. The reduction in capacity of the model occurs quickly. Contacts at this device are located in the upper part of the case. Rust appears very rarely on contacts. However, salt with long-term storage is always formed.

In order to get rid of it, you can just use a dry rag. At this time, kerosene will help with rust. Drain the electrolyte carefully. After this, the tank should stand for about two hours. Then the neck should be thoroughly wiped. Then you need to fill the tank completely with electrolyte. It is important to monitor the level of the substance. After that, the battery should stand for at least three hours. Begin the trimming process with a weak current. Connect the device directly from the negative pole.

Models of the "NK-22" series

Maintenance of alkaline batteries "NK-22" is very simple. Contacts for this battery are made with special protection. It is also important to note that they have a wide mouth. Thus, the electrolyte is very easy to change. If necessary, it is easy to check the condition of the electrodes. Salt on contacts is rarely formed. Rasterization is carried out at a voltage of 3 V. It is also important to note that the impregnation of the plate occurs quickly. Bourne in this model is installed screw type.

Devices of alkaline type "NZh-45" series

These alkaline batteries for electric forklifts may be stored even at a temperature of -30 degrees. The case in this case is protected from rust. Many experts claim that the device can be charged from any source. However, the dressing should be carried out at a voltage of 2 V.

It is also important to note that the device is sensitive to sudden voltage drops. Tighten the nuts in this case carefully. The reduction in capacitance of the model occurs fairly quickly. The current lead in the device is located at the bottom of the case.

Operation of Yuasa series models

These alkaline batteries are very demanding on the density of the electrolyte. The electrodes are in this case lamellar type. Directly the current lead is located at the bottom of the structure. Nuts are often not necessary for the model. Directly the trimming is carried out with a small current charge. When storing batteries for a long time, it is not necessary to change the electrolyte. However, always check the rated voltage before use. Connecting the charger is via the positive pole.

Using the batteries of the "5NK 125" series

Alkaline rechargeable batteries "5NK 125" differ from other models in that they quickly impregnate the plate. Thus, the charging process does not take much time. Separators in the device are of plastic type. The bolt head is located directly next to the electrodes. In order to change the electrolyte, you need to remove the protective cover. Contacts for this model are located at the top of the tank.

The nominal current in the device is 2 V. The capacitance is reduced very quickly. It is also important to consider that the model is allowed to operate even at a temperature of -30 degrees. You can do charging with a weak current. Separately, it should be noted that contacts for this model can be cleaned with a normal rag.