Writing desks with your own hands. Instruction for manufacturing

Home craftsmen often make their own tables. It is quite simple to do this, however, it is important to familiarize yourself with the technology before starting work. In height, such designs can become 75 cm, while the length can be equivalent to 120 cm. In width, it is better to make 70 centimeters. By purchasing the material, you can prefer a planed edging board, the cross section of which is 40 x 140 millimeters. Suitable and sex rail, the dimensions of which are 36 x 135 millimeters.

Preparation of materials and tools

Written tables can be made with their own hands, by storing blocks, furniture screws, and self-tapping screws. Bars can have dimensions of 40 x 60 millimeters. Their length should be equivalent to 70 cm. It is important to purchase 4 units of furniture screws, the length of each of which must be equal to 100 millimeters. This fastening must have a flat hat with a diameter within 10 millimeters. In order to complete the work in a shorter period, care must be taken to have a planer, a grinder, a screwdriver, an electric jig saw, a chisel, and a set of drills. The jig saw can be replaced with a hacksaw, the last of which is certainly in the arsenal of each master. In the absence of a sanding machine , sandpaper can be used, which is pre-fixed to a bar.

Table top manufacture

If you decide to make your own desks, then first you need to work on the countertop. This component of the table will be assembled from 5 boards, which must first be cut to size. Fixation should be carried out to the bars using a screw. The length of the fasteners should be selected in such a way that it reliably strengthens the board, but does not go beyond it. If the work uses a piled board, the table top will be solid, and from the edge of the board, the tongue should be removed using a jig saw.

Making the legs

If you collect the desks yourself, then the next step will be making the legs. They are formed from the same material as the table top. Two parts of one leg should be connected to each other in half a tree. For starters, it's important to implement the markup. On the plywood or fiberboard, you need to draw a rectangle whose dimensions will be equal to A x 600 millimeters, here A is calculated by the formula 750 - b, the last value is the thickness of the table top in millimeters. After the board is positioned along the diagonal of the rectangle so that different edges of the board appear in opposite corners, you can mark the cutting line for the boards, as well as the angle of the joint. Marked blanks must be cut lengthwise, forming a locking joint in a half-tree.

Next, assembling and joining the elements with the help of PVA glue, mixed with sawdust, is carried out. Self-tapping will make the fixation more reliable. The size of the desk you can choose yourself. At the next stage, the assembled legs should be attached to the bars of the product using furniture screws. The stiffener, which should be located between the legs of the structure, should be fixed with screws. Both ends of the table top are closed with blocks, which can be strengthened with nails, which are driven by a hammer blow along the punch.

Final work

If you choose the height of the desk, you can prefer the one that was mentioned above. However, if the table is used by a child, then this parameter can be changed depending on its growth. In any case, at the final stage, it is necessary to sand the surface of the table and cover it with varnish or paint. This will significantly extend the shelf life of the structure. However, you first need to check whether there are any knots and other errors on the surface that can cause injury and splinters.

Making a table with drawers

If you need to make a desk with boxes, the below recommendations will help you with this. For the work is recommended to use furniture boards that are environmentally friendly and easy to handle. The worktop can have dimensions of 1100 x 600 mm. In order to exclude injuries, the front corners can be cut, rounded with sandpaper. The table top will project forward by 20 cm, so you can strengthen it with a bar, the cross-section of which will be 20 x 45 cm. The writing table from the array will be the most aesthetic and durable.

Side bars should be installed on the edge, from the back to the moment of rounding, you need to saw off the elements, and then also round off. At the next stage, the elements are fixed with screws. To start, the beam is drilled in half, so that the fastener freely enters the hole, after screwing inside the hole. After the side bar is in place, you can measure the side components. It should be attached to three screws. On this we can assume that the table top is ready.

Production of drawers for writing desk

A desk with drawers will include two pencil cases, the left one of which has movable elements, whereas the pencil case itself must be made of two sidewalls, the dimensions of which are 1600 x 400 mm. The front and top elements of the sidewalls must be rounded, while the lower ones are filed under the plinth. Four shelves are fixed with screws, and the fifth is fixed at the end for special fasteners.

The next step is sawing the back plate to install the shelf. After the frame of the pencil case can be assembled, corners should be made of plywood. By the same technology, the right pencil case is made. The lower cross member is made of a furniture board with a width of 200 millimeters. This will give the table strength. This element should be fixed at a distance from the floor of 29 cm.

Features of work

The sizes of a desk at independent manufacture you can pick up individually. For the canisters it is necessary to prepare drawers. Their manufacture can be dealt with using plywood, the thickness of which is 6 millimeters. Preliminary material is processed by a grinder, which will exclude the subsequent analysis of the boxes. The bottom is measured taking into account the roller guides. After that end and side walls are made. Do not forget that before mounting the elements must be drilled holes for installing screws. When carrying out these works, you should use fasteners, the size of which is 3 x 20 mm. If the facial parts you will be overlapping, the boxes are fixed in one level with the frame of the pencil case. Shelves for the desk are only needed in some cases, so you need to think before manufacturing whether there is a need for this part of the table. For the installation of boxes the pencil case must be divided into 3 parts, taking into account the location of the lower and upper shelves. It is important to leave gaps between the facial parts. After the sawing is made from the furniture boards.

Conclusion

If you will be made a desk of solid wood or any other material, you must first choose a varnish for its processing. The composition can be applied until the time of assembly or after the completion of all work.