AutomobilesCars

How to glue toning?

Do you have a favorite car and you want to make it even more attractive by toning the glasses? Do you think this is very difficult and you can not cope without the help of a master? After reading this article, you will realize that you have made a big mistake and will find the answer to the question "how to glue toning?"

Every driver loves his car, he cares about it, cleans, cleans and decorates. Tinting until recently was an essential accessory for most cars. The color and throughput of the tinted glass, before the adoption of the latest amendments to the traffic rules, were a personal matter for every motorist. The changes introduced in the code of road regulations today govern the permissible obscuration. According to the new resolution, the throughput of the windscreen should be at least 75%, the side viewing glasses - not less than 70%. Violation of these standards leads to an administrative penalty. This must be remembered.

How to glue a tint

If you still decide, you should not buy cheap film: it is excessively thin and in the kit you will not find a special knife and spatula, which will have to be purchased separately. For gluing you will also need a dry rag, a liquid for washing glasses and a siphon, into which the same means for washing glasses is poured.

Now, when everything is prepared, you can proceed directly to the process of toning. Work should be carried out in a warm room and preferably with an assistant. If the film is glued on the street, it is recommended that all actions be carried out in a calm weather, at a temperature not lower than +20 ° C. The glasses should be thoroughly washed with a substance containing alcohol. It cleans and degreases the surface well. After the glass has dried, a tint film is applied. Here you need to be careful: do not cut the material strictly along the contour. On all perimeter it is necessary to leave allowances in 3-4 cm.

The film corner is carefully tucked and separated from the base. With the siphon, spray the diluted solution on the dark side to avoid gluing. The separated dark layer is applied to the glass and carefully smoothed out with a plastic spatula. The direction of movement of the spatula should be from the center to the periphery. From time to time, the film should be wiped with a damp cloth. Superfluous sticking out edges are cut with a sharp knife, which should go in the complete set. The side windows are also tinted.

Now it remains to figure out how to properly glue the tint on the rear window. Not all drivers can correctly position the film without removing it from the machine. On cars VAZ the cord is removed, and the glass is squeezed out. Since it is inconvenient to work (due to its convex shape), the procedure is divided into two stages. The imaginary line divides the glass into two parts. A film is applied to one half. It is cut with the same allowances as on the side windows (2-3cm). If creases are formed, you will need a building hair dryer. He heats the film and stretches until there is no wrinkles. The second part needs to be glued exclusively in the joint and nothing else. Upon completion of the work, the glass is put in place.

Now it became fashionable to tune not only the glass, but also the headlights and taillights. Such toning of headlights is a laborious process and, moreover, absolutely useless. After all, over time, the edges of the film will begin to exfoliate and reduce all the work to naught. Also apply a vinyl film on the hood, trunk or wings of the car, which makes your car not only beautiful, but also original.

We figured out how to glue the tint. In this there is nothing complicated. It takes only a little patience and a sharp knife. But do not overdo it with darkening. It is better to glue the film only on the rear windows. Remember that for violation of the requirements of PPD for window tinting, a fine of 500 rubles is provided, and from 1 July 2012 - it is possible to withdraw the numbers.

For your information! The size of the penalty does not depend on how many glasses are covered with a darkened coating and what is the light transmission capacity of the "native" glasses of the machine. Therefore, decide for yourself whether you need to know how to glue toning.

Similar articles

 

 

 

 

Trending Now

 

 

 

 

Newest

Copyright © 2018 en.unansea.com. Theme powered by WordPress.