How to apply "bark beetle" plaster to the wall: step by step instruction, features and recommendations

As an exterior decoration of buildings today, a lot of materials are used, among them it should be noted:

• Decorative brick;
• Composite;
• siding;
• Ceramic tiles;
• Paint.

Along with all this, facade decorative plaster is successfully used, as the most common is the "bark beetle", which gives the surface the appearance of wood, eaten by a beetle bark beetle.

Step-by-step instruction

Before applying the "bark beetle", you should familiarize yourself with the technology of the work. The surface must be leveled using cement-sand plaster. It is best to act using the beacon profiles that are installed in advance. The walls will look much more aesthetic. Before applying decorative plaster "bark beetle", it is necessary to install beacons, between which should be maintained a distance less than the length of the rule by 15 cm. Their setting is carried out according to the level, the first should be mounted the extreme rails. Those that are between them can be set up along strings that will be stretched between the extreme beacons from below and from above. In the space obtained, it is necessary to throw in a cement-sand mortar, stretching it with the rule.

Features of surface preparation

On the screed there will be excavations and dents, which must be sealed with a float. In order to speed up the work, you can use poluter. Before applying "Bark beetle", a few hours after the treatment of the wall at the initial level, it is necessary to wipe the base with a half-wiper or grater. To act in this case, it is necessary to move in a circular motion, the plane must be level, this will allow to remove the base from defects. Additional grouting is performed the next day.

Recommendations of a specialist

If you are faced with the question of how to apply "Bark beetle" on the wall, you should familiarize yourself with the methodology of the work. It involves leveling the surface of sand and cement plaster. Its application can be carried out in a hot time, with each day the surface is watered with water from a hose. This will guarantee uniform drying, cement will not crack, and if this happens, the error can be immediately wiped.

The application of "Bark beetle" can be carried out on a wall, insulated with extruded polystyrene foam or foam. For this, the thermal insulation is strengthened by glue, the plaster grid is laid , and the surface is leveled with a malk. The heater should lie on a level, thus it is not necessary to level a wall with plaster. Before using the bark "Bark beetle", it is necessary to allow the wall to dry out, only in this way you exclude the formation of cracks in the finish. For example, for sand-cement plasters it will take three weeks or more.

Application of "Bark beetle"

Thinking about how to inflict a "bark beetle", you should familiarize yourself with the technology, from it you can learn that plastering walls must be done holistically. This indicates that at one time it is necessary to cover one wall, not counting the protrusions. The essence of this process is that each applied area remains fresh, not yet dried. The whole surface will look monolithic, there will be no drops and seams on it. The solution should be stirred with a mixer, you can use a low-speed drill. Sometimes experts use an ordinary drill, it should be thrown off.

Before applying "bark beetle", it must be prepared. First, water is poured, and then powder is poured. The optimum volume of water in the bucket should be 1/3. In order to achieve high quality plaster mixture, it should be well mixed until it turns into a mixture similar in consistency to mashed potatoes. The solution settles for 5 minutes, after it needs to be broken once more, then can be used.

The structure of the finish will depend on the manufacturer and the brand of the product. However, these factors are also influenced by the master. For example, to form horizontal strips, the solution must be applied in this direction. If it is necessary to get a vertical structure, then the movement of the hands should be directed from the bottom up.

When creating a particular structure, you will be able to assess the importance of pre-finishing. The smoother the facade plaster, the clearer the relief of the "bark beetle", because it is created thanks to pebbles in powder.

Decoration of a layer

If you have a question about how to apply plaster "bark beetle", then you should know that you can perform these works in circular motions. After drying, the surface can be dyed with acrylic. Staining of plaster is not a matter of personal choice, it is recommended by the manufacturer, although the wall for some time can stand unpainted.

Features of work

Quite often, the plaster described in the article is produced in the form of a ready-made mixture, which does not presuppose the need for preliminary preparation. After the acquisition, you can immediately proceed to the application phase. Use a steel trowel for work. To protect neighboring surfaces, an adhesive tape is pasted on them along the outer perimeter. The plaster should be applied in accordance with the thickness of the layer, it should be the same as the grain diameter. If you are thinking about how to apply plaster "bark beetle", then you should pay attention to the fact that the mixture is stretched on the wall in the same way as the putty.

It is important to achieve such an effect, in which small grooves appear on the fresh layer. This will indicate that you have been able to achieve the optimum layer thickness. After this, an invoice is created, for which it is necessary to perform circular motions on a fresh layer with the help of a plastic float. Sometimes on the surface of the grater sticks plaster, it can be considered normal. 15 minutes after application, the "bark beetle" should be treated again with a plastic float, this time the pressure should be more impressive. By this time, the composition will thicken a little and dry. Only after the first pass the surface is cleaned. This will form the final appearance and drawing.

Quite often novice home masters think about how to correctly apply "bark beetle". Experts advise: it is important not to overdo it, because with more approaches the wall will be more smooth.

At the final stage of applying the mixture, it is necessary to treat all joints with a float. If the joint has not been wiped, do not let it dry, because it will be visible on the finished wall. On the surface of the plaster it is more convenient to apply together, one master will perform a throwing and pulling of the mixture with a spatula, making the first mashing. The second master will form the final form in 15 minutes. Once the walls were plastered, the paint tape can be removed. The protruding edge of the "bark beetle" is cut with an ordinary clerical knife.

Final work

Now you know how to apply "bark beetle" on the facade. But it is important to get acquainted with the technology of the final works. They assume a glazing. To do this, select a quality acrylic lacquer, which can be matte or glossy. Its preparation can be carried out in such a way that the desired color is obtained. In nail polish you can add nacre and shine. For this, a certain technology is observed.

The plaster after the application is left for a day, and before the application of the varnish the surface is primed, so that the coating composition does not cover the surface with stains. If before you, too, the question arose of how to correctly apply the "bark beetle", then you should take into account that these works are carried out using a steel spatula, which is convenient to use for removing excess lacquer.

For reference

Sometimes people ask themselves whether it is possible to apply "bark beetle" to "bark beetle". Experts give an unequivocal negative answer. This is because the grooves are formed on an exceptionally smooth surface.

Conclusion

Now you know how to apply "bark beetle" on the wall, but before starting work, you need to become more familiar with the main varieties of this material. It can be designed for facades or for interior work. On sale it is possible to meet and universal mixtures.