Aeroglisser with your own hands on the radio control

Lovers of making different "toys" on the control panel will probably be very interested in how to make an air-roller with their own hands. This boat, which is really assembled on its own, will be a wonderful gift to the child or help in fishing.

What materials will be needed?

In principle, any person will be able to assemble an airslitter with their own hands. The only thing is - have to buy some details (if they are not at home at hand). You will need only:

• Foam, foam or ceiling.
• Scotch.
• Glue.
• Wires and a motor with a propeller (or impeller).
• Drawing (although you can do without it).

If you give a child this wonderful homemade, it is best to use an impeller. Its advantage over the propeller - the baby will not be able to cripple his fingers. But the thrust of the impeller is small enough - about 500 g. But if you make an airglass easy, then it is quite enough.

The beginning of the construction process from the penoplex

If you use an impeller as a motor, the best way is to take sheets of a penopolix with a thickness of 20 mm. If it is not near at hand, then you can build an air-lift with your own hands from the ceiling.

If the airglass is not too large, you can take sheets with a thickness of 40 mm. Excellent buoyancy indicators in combination with ease make penoplex an excellent material for this homemade product.

In order for the air-slip to be stable on the water, it is necessary to perform balancing by placing all the parts in a special order. Since the heaviest part of the boat is the battery. It should be installed as low as possible. For this, it is possible to cut a notch in the body under it. But it should also be borne in mind that the ceiling is a brittle enough and thin material. Therefore, it is necessary to strengthen it with something. For this purpose, a ruler (the usual school wooden ruler) will do. With glue or epoxy it is fixed in places that can not withstand loads.

After the electrical equipment of the future boat was installed, it is necessary to glue the bottom to the hull. This can be done with the help of Titan glue and wait a while for complete drying. After that, you can do add-ons.

Superstructure on the self-propelled aeroglizer

In order to make the superstructures on the deck of the future boat, you can use ready-made drawings, or you can try to do something your own. Of course, all models have some features that unite them. So do not be wimpy.

Mounting for the impeller can be made from two connected parts of the penoplex. For this it is necessary to cut a rectangle, and in it to cut a circle under the engine, and then the resulting rectangle to cut in half. This design allows the engine to be removable (for replacement or repair). In order to reliably fix the impeller and not be afraid that it will jump out at any time, you can fix it with the help of the same ruler and a pair of screws. To do this, it is pasted between two halves of the penokleksovogo rectangle, and then the resulting design is glued and fixed with screws.

The superstructure in the form of a wheelhouse will cover the electrical equipment from splashes. Fastening is made with the help of glue. You can use hot glue, but if the aeroglisser will be used in the winter, then this is not the best choice. In addition, in the wheelhouse will have to make holes for ventilation.

Boat control

In order for the airglasser to be managed somehow, he needs to attach the rudder to the direction. The finest ceiling is best. A rectangle is cut from it. To fix the steering wheel, you can use any rod of 3 mm cross-section. In addition, it is necessary to take into account that when driving on water, an airslitter will "pick up" the nose and the steering wheel will be in the water.

Vessel sealing

The boat is able to move on any surface, whether it's snow, water or grass. It is not ruled out that dirt and water get inside the homemade article. To prevent this, you have to arm yourself with alcohol, epoxy and a brush. Since the airglasser with his own hands on the radio control, the antenna must be hidden in a tube of carbon. Then it is necessary to dilute the epoxide with alcohol and apply a brush to the ship. This not only protects against water, but also makes slip easier. And an additional plus from the epoxy coating is the airglysser, made by hand, becomes stronger.

«Spillovers» and accessories

To distinguish your airplane, you can attend to some "decorations" and useful additions. Balloons with paint are perfect for painting a ship, and with the help of an adhesive tape you can add something to the body or decorate the steering wheel. But it should be taken into account that the weight of the model increases, which means that the speed will be lower. The main thing is not to overdo it, because the boat can simply roll over in the water. In addition, the airglasser can be equipped with flashlights and LED light bulbs.

Aeroglisser made of foam plastic

The foam has the same buoyancy characteristics as the foam foam. Therefore, the creation process is not much different. And on the Internet you will not have to search separately, how to build an air-roller with your own hands. As well as in the first case, it is possible to make an airslitter with your own hands (drawings of boats will help to facilitate this process). Or show your imagination and collect something of your own. And to strengthen the construction you can use building scotch. They are wrapped around the bottom. Wooden rulers can not be used to harden the structure.

Aeroglisser for your own fishing

To the lure of fish has become not only a simple process, but also fascinating, you can use a radio-controlled airglysser with your own hands. For permanent use, it is best to make a solid boat made of plastic or plywood (although for these purposes plastic or PVC panels are more suitable because they do not rot)

1. Aeroglisser with your own hands (the drawings will make the task easier) do not necessarily start with the study of schemes. You can make 3D layouts in the corresponding program.
2. Next, you need to make a drawing, which will cut out all the details of plastic or plywood.
3. Now that the drawing is ready, you can start cutting.
4. Bonding can be done with hot melt glue, Titan glue or Moment glue (if plywood is chosen as the material for the case, it should be pasted with fiberglass impregnated with epoxy resin).
5. Nasal holes should be filled with mounting foam so that the boat does not sink.
6. Next, you need to attach the engine. It will look almost the same as the impeller. Fixing it in the hull of the boat, it is necessary to protect the water intake opening with a grate. This is necessary in order for algae, gear, etc. Did not wind on the screw.
7. Electrical equipment will need to be purchased. If the fisherman decided to seriously tackle the lure with the help of a self-made airboat, then it's best to go to the radio electronics stores and buy a suitable engine and remote to it.

The cost of the received "toy" will be about six thousand rubles. Agree, compared to what is offered by fishing shops (boats from 30 thousand rubles), this is still divine.

For any inveterate fisherman, this self-help will help to bait fish. Usually the lure is thrown by the hand for a certain distance, the boat is able to simplify this process. Doing an air-lift with your own hands for fishing, you need to consider that the food will somehow be dropped from it into the water. In order to solve this problem, you can go on the path of least resistance - make openable containers with lure, and attach a strong thread or line to the door. When the aeroglisser reaches the right point, you just have to pull the rope.

Mission "Rescuer"

Ambitious fans of aircraft on the radio control can find themselves in a difficult situation - their model can fall into a pond, and you can not get it. Now we are talking about models of hydroplanes, because the remaining models of aircraft, most likely, immediately go to the bottom.

So, a fan of radio-controlled aviation was in trouble. The plane was in the river. In order to pull it out, it's enough to attach the end of a strong rope to the body of the airboat. And then using a boat to pick up the plane and pull it out of the water.