Snow-removing machine by one's own hands: step-by-step instruction

Snow, of course, is good. But when its a moderate amount. Yes, and in this case, the inhabitants of the private sector are forced to constantly remove it. It is often difficult to manually perform such work. Although the shovel is the right tool, it takes quite a long time to clean up a large plot. Let's talk about how to make a snow-removing machine with your own hands. This will help to save money and at the same time acquire the necessary equipment.

General information about snowblowers

Such useful technique appeared long ago. It was invented by the Canadian, who was constantly forced to fight with mountains of snow near his house. Since then, the snow-harvesters have significantly improved and become more productive, economical and convenient to operate. Before you proceed directly to assembly work, you need to understand the priority design. That is, the snowplower will drive by himself or we will move it manually. The second option is cheaper and simpler in technical terms. In general, we will consider several ways of how a snow-removal machine is made by oneself. Or rather, we will talk about machines of different types. But about all this in order.

Screw snow blower

As the basis, we take an old motor from the motor block. Such a motor is perfect for us. For the assembly of the auger body, we need sheet metal. Frame construction is made of a steel corner section of 50 x 50 mm. For the organization of lateral details, the most common 10 mm plywood is needed. Also we need to hold onto something. A pipe can be used as a handle in half an inch.

The air intake of the engine, which will ensure its cooling, it is desirable to additionally protect, which will prevent the entry of small particles of snow. The width of the machine in our case will not be more than 65 cm, and its working body will clear the track width of 50 cm. This will give us the necessary maneuverability and ease of moving the unit. Well, now we turn to the practical part and consider how a high-quality snow-removal machine is made by oneself.

Screw manufacturing

A ¾ "pipe can be used as the screw shaft. In it, you need to make a propyl, which will fix a metal spatula. The principle of action will look like this. In the process of working on the transport belt, the discarded snow will move to the blade. From there he will lean back and forth. It is desirable to equip the screw tube in the following way. Install a metal spatula and four rubber rings on it. As the material for the latter, an old transport tape with a thickness of at least 1.5 cm can be used.

It should be understood that the auger tube will rotate in self-centering bearings. It is necessary that they are of a closed type. This will prevent moisture from entering the enclosure and increase the longevity of the unit. The transmission can be either belt or chain. The first is less noisy, but also not very reliable, with jamming can fail.

Scraper snow plow with your own hands: drawings and assembly of the structure

The walls of the machine body must be larger than the screw itself. This is necessary in order to prevent the walls from touching the working body. Usually, the engine installed on the snowplower can be used at other times on a different technique. Therefore, it is recommended to provide a quick-detachable structure. A special platform is being built for this purpose. This solution has a lot of advantages. Firstly, it is much easier to clean the tool after work, and secondly, after removing the motor, the unit will become many times easier. All metal elements can be welded together, but it is desirable to use threaded connections. Also pre-prepare the drawing, which will guide you when assembling. After that, the unit can be put into operation.

Rotary snow blower

In terms of design, this unit is not too complicated. It is great for snow removal on sections of any size. To build the structure you will need a lathe and a welding machine. In principle, such equipment can be found in almost any workshop. As a basis, we will use a gasoline engine, a throttle control cable and a gas tank.

The first step is to select the workpiece, from which the rotor will be manufactured later on the lathe. If you do not have to bother with this desire, then you can buy it in a specialized store for little money. Externally, the rotor resembles a disk. When it is installed on the hub, then it is attached to it with blades, usually 5 pieces. Mounting the blades is preferably done by welding. Blades on the back side can be equipped with stiffeners, which will increase the efficiency of the structure and its productivity.

On the fan it is necessary to put on a casing which will protect it from hit of various elements. It is worth noting that the various schemes of assembling the main elements of the snow-removing machine means placing the cylinder head at different angles. It is best for the effective cooling to place the cylinder at an angle of 90 degrees.

Do a snowplower yourself

Our rotary snow plow is almost ready. It remains to finish the assembly, and the equipment can be put into operation. The shaft must be placed on the rotor. It is mounted on pairs of ball-type bearings. Fixation to the body is best done with a clamping ring and a pair of bolts. Directly rotor to the body of the machine must be secured with a clamp. It will also hold the clamping ring, which is very convenient. It is desirable to equip the machine with removable scrapers. This is necessary in order to be able to adjust the width of the grip.

In some cases, this is an extremely convenient feature, which, by the way, is not available in all purchased models. The range of snow removal in our case will be of the order of 6 meters and this at an aggregate weight of 18 kilograms. In general, you get a maneuverable and lightweight unit. As you can see, it is quite possible to build a snowplower with your own hands. How to make a homemade snowplower, we figured out. Now a few more important nuances.

It is worth paying attention to

If any large and solid element gets into the engine, be it a stone or a piece of ice, it can break down. To prevent this, insert safety bolts into the structure. Do not neglect the bearings of a closed type, but this has already been said a little higher. If you decide to make a snow-removal unit with your own hands on an electric drive, you should understand that it will be effective only at short distances. Otherwise, similar equipment is more economical and less noisy than a gasoline engine. But you have to get used to the wire that will haunt you everywhere. Pay attention to the material used in the assembly. It should be as light as possible, but durable at the same time. If the unit is too heavy, working with it will be problematic.

Conclusion

You can also make a snow thrower for a motoblock with your own hands. Drawings in this case is simply necessary. It is on them will be indicated the main dimensions and design features of the unit. In general, such a decision makes sense, especially since such a technique will move on wheels, which is very convenient.

We have dealt with this topic. There is nothing complicated, but it will take time to assemble, because something needs to be bought, and some details can be carved out by yourself. When the build process is finished, you can bring the design to order. Here you have in mind cosmetic work, such as painting, polishing, etc. As a result, your home-made snowplow will not yield to any purchase. But you will save a significant amount, and experience in such cases, you will be typed and will be able to give advice to beginners.