Replacement of clutch VAZ-2107: instruction, recommendations. Replacement of clutch VAZ-2107: price

The VAZ-2107 clutch is replaced by a certain algorithm, which will be described below. To begin with it is worth remembering the history of the car, it turns out that it was most likely designed for one sole purpose: to bring maximum horror to the rotten capitalist world. And the use of the "seven" as a means of transportation was clearly not envisaged. But in the repair of the car is simple, like the famous T-34 tank. The only inconvenience is removing the starter, and this procedure will have to go through during the dismantling of the gearbox. This process will be described below.

What you need to stock up

Despite all the shortcomings and simplicity of the car, when repairing you will need a special tool, without which you can not do. First of all you need a pin - a suitable diameter metal tube (you can even hollow inside). With its help you will center the position of the driven disc relative to the clutch basket. Depending on the age of the car, its technical condition, and the cleanliness of the driver, the replacement of the VAZ-2107 coupling may take a different time. The price of the whole set will be about 2000-2500 rubles. Of course, we need to mention the nodes that need to be installed.

Firstly, this is the entire set of clutch - the basket, the bearing, the driven disk. Secondly, you must change the bolts and washers with which the disk is fastened to the flywheel. Thirdly, if you plan to replace the VAZ-2107 clutch cylinder, you still need to buy brake fluid and new hoses. Fourth, you will need to assess the condition of the flywheel crown. Fifthly, you remove the cardan shaft, so the possibility that the crossings have become unusable and also require replacement is not ruled out. Sixth, the state of the cushion box and the suspension bearing is unknown . In other words, this miracle car can bring many "surprises" to the car owner, who does not monitor the technical condition.

Preparation for repair

First of all, drive the car to the lift and disconnect the battery. Pay attention that it is necessary to disconnect the storage battery. When the replacement of the VAZ-2107 clutch is made, the box, the starter is removed, and on the last one - the power wire of the large section. And if he closes on the mass, then the fire can not be avoided. And do not forget that the car is rear-wheel drive (of course, in the good sense of the word). And this means that it has two rear wheels that are leading - the torque is transmitted to them from the engine through the box and the driveshaft with a reducer.

What does this mean? About what you need to install the wheel chocks under the rear wheels. Yes, at least bricks, so that the car does not leave. In a broken state it is capable of horrifying not only the capitalist countries, but even normal and adequate people. And it does not matter, completely change the site, or only the replacement of the clutch disc VAZ-2107 is planned, you need to remove the box in any case. Therefore, all the requirements described below must be fulfilled.

Is it possible to do without a pit / lift?

But the first question arises immediately after the appearance of the idea of replacing the clutch. Is it possible to do without a pit / lift / overpass? Unfortunately, not every motorist has such amenities. The answer will be brief - you can. But it's not complete, as you could see. Therefore, it is worth to describe the procedure of repairing without any comforts. If you are a lean physique, then it is enough for you to lift a car of centimeters by 40-50. But the convenience, of course, does not add this position of the car. If you live in a rural area, then make a small trench - a couple of meters in length, 50 cm wide and in depth as much - is not difficult. In this case it will be much more convenient. But it's better, of course, on a normal pit or the lift is easier to repair VAZ-2107. A clutch fork, replacement of which is also sometimes necessary, is removed and put only after the removal of the gearbox.

Stage one - on top of the machine

So, the dismantling of the VAZ car begins in parts to get to the bottom of the truth, what is it that horrifies the decaying capitalism? First of all, disconnect the battery. You need to remember again, so you will not forget. Then, disconnect all the two wires that go to the starter, then remove it. It is possible that it was the starter that horrified, since it is a problem to remove it, the lowest mounting nut (if any) should be screwed out with a head with a cardan and an extension, and not a small one.

After that you sigh deeply, because the replacement of the VAZ-2107 clutch has just begun, there is still so much to do. For example, disassemble the gear lever. It is made of plastic parts, but their disconnection is fraught with the production of chopping-cutting hands injuries from a screwdriver. But if you managed, then continue what you started. In the hands of keys on the 19 and forward, twist the bolts, which the gearbox and ICE are connected together. And at the same time unscrew the intake pipe from the exhaust manifold, as it will interfere.

Stage two - bottom of the machine

Now settle down under the car and perform the following manipulations:

1. Disconnect the drive drive from the flange on the gear side. Mark only the position of the splines, otherwise after assembly the cardan will be terribly buzzing.
2. Unscrew the suspension nut of the outboard bearing. And do not lose them, it is better to immediately nashivlyayte all gadgets.
3. Knock out the cardan shaft with light tapping. Throw it aside so as not to get in the way.
4. Tear off the nuts on the pillows of the box. Until the end until that, do not twist.
5. Remove the clutch slave cylinder and secure it so that it does not accidentally damage the hose.
6. Unscrew the speedometer cable and disconnect the reverse sensor.

That's all, now under the box put the support, scrap pushes the transmission from the engine block. A little anguish and the box comes off.

Replacement of clutch discs

But now only the replacement of the VAZ-2107 clutch will be carried out, all previously described was related to the preparatory work. The procedure for replacing the clutch is very simple. Twist out six bolts, remove the basket, together with it and the disk will come down. After that, put the new elements, nazhlyaete six new bolts. Sometimes even a plastic tube for alignment comes in the kit, if not, then put a suitable blank in the disc. Evenly (diagonally) tighten the bolts of the basket, checking the alignment. All, now put a new squeeze and you can collect the car. Problems with the clutch now will not be long.