Profiled sheeting C10: technical characteristics, weight, size, application

Profiled sheeting C10 is one of the widely used products in civil and industrial construction. The most common galvanized profile is used for the erection of individual houses. The material gained high popularity not only because of its low cost in comparison with analogues, but also due to a successful combination of lightness and strength, as well as ease of installation. This allows you to save not only at the time of the purchase, but also in the process of construction work.

Application area

One of the reasons for the high popularity, which has profiled C10, is its versatility. The material is applied in almost all areas of construction: for the installation of roofing, the construction of prefabricated buildings and structures, frame, insulated wall and panel structures, fences, fences, ceilings, and prefabricated sandwich panels.

If it is necessary to lay the C10 as a roofing deck, the crate must first be set up, with the step between the elements being 0.5 meters (but not more than 0.8). This figure is relevant for roofs with a large angle. The corrugated board C10 is produced according to the state standards Р 52246-2004 with the use of cold-rolled steel, which is protected by a zinc hot coating. The most popular is the C10 with a polymer coating. The decorative protective layer makes the material attractive externally and extends the life of the profiled sheet. On sale you can find a corrugated board of grade C10 with a one-side coating, where a special lacquer is applied to the inside. A sheet with two-sided spraying is used for the construction of fences, which allows to provide the same aesthetic fencing on both sides. In the stores, the C10 profiled sheeting is realized from some manufacturers, which has a figured texture and is intended for the construction of fences of residential buildings.

Specifications

If you want to choose the right material, you should pay attention to the numbers that are indicated next to the markings. As an example, you can use the designation C10-1000-0.6, from which you will learn that before you a wall sheet with a trapezium height of 10 mm. The useful width of the web is 1,100 mm, and the thickness of the metal is equivalent to 0,6 mm. The modern consumer is offered to purchase material marked C10-1000-0.5 and profiled sheet C10-1000-0.7. The first of these has a sheet thickness of 0.5 mm, while the thickness of the second one is 0.7 mm. One square meter of a profiled sheet of lesser thickness weighs 4.6 kg, but a 0.7 mm sheet will weigh 6.33 kg.

Despite the fact that the difference in thickness between these types of material is negligible (the second weighs 1.73 kg more than the first), it increases the load on the system, especially for large roofing dimensions. Therefore, acquiring C10 profiled sheeting, it is necessary to calculate the roof area, which will be affected by the snow load characteristic of a certain region. The sheet dimensions differ in width of the initial workpiece. This parameter can be 1 000, 1 100 or 1 250 mm. There is also a useful width, which is equal to 900, 1,000 and 1,100 mm.

The weight of the material, depending on the thickness

Profiled sheeting C10, whose weight varies depending on the thickness, has a density of steel, equal to 7 800 kg per cubic meter.

• One running meter of the product will weigh 4.45 kg if the sheet thickness is 0.4 mm. At the same time, there will be 4 kg per square meter.
• With an increase in thickness to 0.45 mm, the weight will be 4.05 kg per m ² and 4.78 kg per p / m.
• A sheet thickness of 0.5 mm gives a weight equivalent to 4.6 kg per m ² and 5.4 kg per running meter.
• Product 0.55 mm has the following indicators: m ² - 5.4 kg, and p / m weighs 5.9 kg.
• With a slight increase in thickness to 0.6 mm, the running meter of the product will weigh 6.4 kg, and the square meter - 5, 83 kg.
• The sheet 0.7 mm has a weight of 6.33 kg per square meter, and the weight of the p / m is 7.4 kg.

Additional features

The profiled metal sheet has a certain stiffness and strength, which was achieved thanks to a deep 10 mm corrugation. This allows the use of the canvas for structures and structures of high complexity. The material is resistant to corrosion, and the polymer coating increases the durability of operation. The leaf profile is economical, as well as resistant to any climate. Without a coating, it can be used to make the formwork to fill concrete with a foundation. Acquiring C10 corrugated board, the technical characteristics of which motivate consumers to make a choice in its direction, you get the opportunity to reuse the canvas, saving money. The material is easy to install, it is easy to cut and drill, which facilitates the work of installation teams.

Cost

Profiled sheeting C10, the price of which will differ depending on the thickness, is supplied with galvanized and polymer coating.

• In the first case, the product of the smallest thickness (4 mm) will cost 196 rubles. For running meter.
• With an increase in thickness to 0.5 mm, the price increases to 229 rubles. For p / m.
• If you are interested in the thickness of 0.55 and 0.7 mm, then for the meter of these materials will have to pay 249 and 307 rubles. respectively.
• The price will increase if the corrugated sheet has a polymer coating. For sale this material is presented in several versions - with a thickness of 0.4 mm, and also 0.5 and 0.7 mm. In the first case, the cost is 228 rubles. For p / m. For a sheet 0.5 mm thick, you will have to pay 268 rubles. And for the meter of a seven-millimeter corrugated board - 368 rubles.

Features of application of corrugated board

Corrugated iron can be stacked on almost any roof. The distance between the rafters should be equal to the limit of 600 to 900 mm. Between the sheets are fixed roofing rivets, and for laying on the roof should be prepared roofing screws. For them, holes are made first. If the sale could not find the building fittings of a suitable shade, then the screws can be replaced with screws with a hexagon head. You should choose fasteners with a plastic or rubber washer. If you decide to use the latter option, you must first drill holes in the mounting location of the fasteners, the diameter of which should be 0.5 mm larger than the screw. The corrugated iron should not be installed on the roof with the help of nails. Technology is not provided for the reason that under the influence of wind nails can not hold the sheet. Screws and screws must be installed strictly vertically, which eliminates water leakage.

Board of specialist for sheet reinforcement

Sheets of corrugated board are installed on the crate and are fixed in the places where the wave is adhered. Approximately 8 fasteners will be needed per square meter. You should try to keep the distance between them the same. To the first and final crate, the sheets are attached to the area of each wave, since these areas will have a large wind load. To the intermediate crates, the corrugated board is fixed through a link. At the longitudinal joints, the step between the fasteners should not exceed 500 mm.

Important nuances

The corrugated sheet can be stacked according to one of two existing methods. The first provides for the vertical arrangement of the web, while the second provides for the creation of a three-sheet block. Vertical packing is used for products having a drainage groove. First, the first sheet is laid, which is fixed temporarily, then the first sheet of the second row is placed. Next comes the second cloth of the 1st row. Next, you should install the second sheet of the second row. This will give you a block of 4 canvases, each of which should be aligned and fixed finally.

If you want to strengthen the sheet on the wall, then it is worth using a metal guide profile. First, the vertical profiles are fixed, which must be fixed to the previously strengthened brackets, then horizontal bridges should be attached between them. Their location should be convenient. By the time the frame structure is ready, it is possible to start fixing the wall profiled sheeting by using self-tapping screws.