Mounting snow-holders yourself: technology, features and reviews

Every winter, the snow, suddenly falling from the roofs, causes trouble, and sometimes accidents. It traumatizes people, and also causes damage to property. This could be avoided if the owners of the buildings installed the snow-holders on the roof.

Basic design of snowshoes

Installation of snow chains should only be carried out after selecting the appropriate structure. Among others, it is possible to distinguish a lattice variety, which has the form of rigidly fixed brackets on the roof, and lattice compartments are located between them. Such constructions are made from rectangular corners, as well as pipes and frames. As an extension, the cross bars act. If it is necessary to extend the structure, shorter sections must be joined together.

Snow covers on the roof, the types of which are described in the article, can be tubular. In this type, the brackets are fixed to the roof roof or roof rafter. Metal pipes are passed through them. Depending on the distance between the pipes and the space between the lower pipe and the roof, it will be determined how much snow can hold the device. If it is known that the design should be more powerful, then the strength can be increased by reducing the distance between the pipes.

For reference

Snow covers on the roof, the types of which can be very different, should evenly distribute the snow load on the roof surface. In the case of tubular snowshoes, their installation should be carried out along the line of the bearing wall.

Features of snowshoes in the form of hooks and angular, as well as plate structures

Snowshoe-hooks are hooks that will not hold snow in a large volume, so they are suitable for roofing with regular cleaning. They are chosen for soft structures that are covered with bituminous tiles or any other similar materials. Usually snow hooks in the form of hooks are used as a supplement to other devices of similar purpose.

Installation of snow loaders with their own hands can be completely carried out by any home craftsman, they are no exception to lamellar or corner structures that perform their function on metal roofs, as well as structures made of galvanized steel or european tiles. They are made of the same material as the roofing, this can be called an advantage, whereas their inability to hold up a large volume of snow is a minus.

Comments of consumers on the peculiarities of choosing snegozaderzhateley

The maximum angle of the ramp for soft roofing can not be more than 15 °, such roofs are flat, so the dangerous snowfall from them is quite rare. This indicates that the installation of snegozaderzhateley in this case will not be too complicated. Among other things, a good reason to reduce the power of snowshoes is the roughness of the soft coating. According to the buyers: the more rough the surface, the less the angle of the ramp, hence the risk of snow falling.

Mounting snow holders is accompanied by many advantages. These structures, as the users emphasize, provide an even melting of the precipitation. Avalanche convergence is practically impossible, among other things, the load of solid sediments will be well distributed over the entire area. If we talk about shortcomings, then these designs do not. And if some parts of the roof are damaged when the snow melts, the snow holders were installed unprofessionally.

Mounting technology of snow chains

In a large assortment today, snow chains are presented on the roof, the installation features of these structures will be mentioned below. However, if you are not sure that you will be able to cope with the work yourself, then it's best to turn to specialists. For example, hooks can be installed only in the overlapping stage, but not afterwards. The design assumes fixation under the cover itself, otherwise the system will not be able to hold snow. On the finished surface, hooks are not installed, as in addition they will have to carry out roofing re-laying.

It is advisable to design the works even during the construction phase of the building or in the process of overlapping, as well as repair of the roof. If you decide to install snow-holders on metal roofing, the best solution will be latticed structures, this method is most effective and simple. Such a snowshoe system will be able to hold pieces of ice and snow. The grating barrier copes with heavy snow, if you choose the right elements. Using hanging supports or chisel elements, the metal grill must be installed directly to the edge of the roof. Covering the roof does not matter, it is quite possible to install a snow blower of this type on any roof.

Recommendations of installation specialists

The special features of mounting snow covers are also in the fact that the suspension supports are hooks that do not need to be screwed. They need to be fixed on the lathing, while the pile supports are installed in the rafters area, most often it is done on the soft roof. If we are talking about lamellar snow-holders, they are a budget version, although they are made of a material similar to roofing. Reliable protection with these inexpensive devices can not be achieved, among other things, their use on roofs, the slope of which exceeds 30 °, is unreasonable.

Installation of a tubular structure

Installation of snow-holders of the tubular structure provides for the implementation of a certain algorithm, it involves marking, on which the support brackets will be installed. In doing so, you should use a puncher, with which you can create holes, they install self-tapping screws. The holes of the bracket are fastened to the pipes of the snow holder. In order to make the length suitable, the elements are joined together, thus one-sided crimping should be used. The joints are bolted together. Similar actions should be carried out on each side of the building along the entire perimeter. Finally, the bolted connection is checked.

Installation of snow loaders on metal and profiled sheeting

If the installation of snow covers is to be carried out on the above-mentioned coatings, it is necessary to form fences that are installed on the carrier crate. Their fixation is made to the end, for this you should use screws 8x50 mm. In order to ensure a higher density of fasteners and reliability, the holes should be sealed with rubber. The optimum distance between the anchorages should be chosen depending on the slope of the ramp and the length. This parameter can vary from 0.5 to 1 m.

Conclusion

Mounting snegozaderzhateley own hands can be conducted and on the seam roof. For this, a counter element is installed, and the snow holder is attached to the base using hexagonal bolts with dimensions of 8x25 mm. Mounting should be installed in those places where the crate is continuous.