Mounting for the tablet into the machine with your own hands

Tablet computers, or simply tablets, have long been suitable for use in cars. Car enthusiasts have adapted these thin and powerful devices as a replacement for full-time receivers, gps-navigators, and some experts in electronics and programming even use them as an on-board computer. Tablet - it's convenient, practical and in traffic jams is not so boring. And if there are children, then you can take them with your favorite games or watching cartoons in long and tedious trips. Some even adapted the tablets as DVRs, and they perform their functions perfectly.

How to fix a tablet computer in a car? Types of holders

Multifunctionality, multimedia functions, as well as minimum dimensions and power - all this is very, very good. It remains only to make the mount for the tablet into the machine.

Today, the market is literally full of different types of bindings. There are many such holders.

So, among all the devices the following constructions stand out:

• Frame universal. Most often installed on the center console.
• On the suckers (attached to the car windshield).
• Anti-slip mats.

Many do not want to bother with the choice and purchase a universal mount for the tablet into the machine. These structures can be adjusted in height, width and other parameters. Mobile devices of any diagonals are freely accessible in these holders. You can rotate the device both vertically and horizontally. There are also models from well-known manufacturers, however they are few and they are expensive.

Where to mount the tablet?

For these purposes, there are only a few places in the car. You can mount the holder on the dashboard, on the glass on the right, on the grille of the ventilation system. You can also install the computer from the back of the headrest. We will analyze the pros and cons for each of these places.

On the torpedo the tablet will look perfect. Often they are fastened as if he was always there. But such designs are not on sale, so motorists and car owners prefer to make such devices themselves. It all depends on the sleight of hand and imagination.

To the right of the driver, you can install the tablet mount into the machine on the glass. Naturally, you can buy a ready-made design, or you can make it completely independently. It is much more interesting, and it also gives an interesting experience.

Mounting for the tablet into the machine with your own hands

So, here we have reached the most interesting part of the article. Previously, many before they became car owners, had bicycles and motorcycles and regularly "kolkhozili" for them something in the absence of necessary spare parts. So here, because the search for easy ways is by no means our method. We will try to make the mounting for the tablet into the machine with our own hands. This is very interesting and economical.

Mount the tablet to the grille

To make the mounting for the tablet into the machine on the duct, you need a device, a little stainless steel, a welding machine, and a metalwork tool.

This homemade design has a number of advantages over rather flimsy holders from Chinese brothers. The design is very convenient to use, it is very easy to manufacture, it does not take much extra space in the salon of your car. For manufacturing, you only need skills to work with metal and a welding machine.

The design does not have any disadvantages. It is very easily removed if necessary, it is a universal mount for the tablet in the car on the torpedo. In general, you can come up with a lot of variants of such constructions. You can use different clips, brackets.

Where to begin?

First you need to find a stainless steel. Next, you need to measure the strip for making a stand. 2 vertical strips are recommended. The required stripes should be 1 cm wide and 17 long. You also need to prepare one horizontal strip of 25 cm in length and 1 cm in width. Next, you need to cut the stripes and bend their edges. So it will be more convenient to use this thing.

The upper parts of the obtained strips need to be folded more than the lower ones. A construction similar to the integral should be obtained. The bent upper part of our strips will cling to the air duct grille, and the lower one will be clamped to hold the tablet. The horizontal strip should be fastened in such a way that it keeps the high-tech device from lateral displacements. Then such fastening for a tablet in the car can reliably hold the tablet, and it will not fall out when driving on our roads.

You can also make additional inserts in this design. They do not have any functional load, but slightly increase the slope of the tablet.

As a decorative treatment, you can glue the resulting holder with a cloth, skin or anything else. As a result, the fixation for the tablet into the machine hooks into the grille of the duct and is reliably held there.

We mount the computer instead of air ducts

This is the way to insert the tablet PC into the dashboard of the car. The mobile computer will be mounted in the middle airway. This method is suitable for cars VAZ.

What to do?

First you need to remove and disassemble the duct housing. By the way, to disassemble it is not so easy. There are many small details. Disemboweled? Now you need to take a frame and try it on the tablet. The frame is suitable for small devices. If the mobile device is inexpensive, then perhaps the screen will fade. Therefore, it is desirable to drown it in a niche from ventilation.

Further after all the measurements, it is necessary to cut off the partition between the two ventilation panels. Then, when we have a single niche, we need to try once again the design there from the tablet and the frame. Depending on the results of the measurements, it may be necessary to add a little more to the panel with ventilation.

Next, you need to glue the frame on the double-sided adhesive tape to the screen of the tablet, to its non-working part. Then insert the structure into the cavity and place on a double-sided adhesive tape. When everything is done perfectly, you need to process the places that used to be the partition. It needs to be ground, primed and dyed, possibly, and zadekorirovat.

Also, as an attachment, you can ask your friends for the bracket from the broken holder and make yourself a metal frame or strips to directly hold the mobile device and secure it anywhere, for example, so you can make the tablet mount into the car on the headrest. In this case, the bracket of the finished structure will not bother to create it, and the metal holders will be much more convenient than the flimsy plastic parts. Children will thank you for the tablet on the back passenger.