How to set the profile for siding correctly?

Metal and polyvinylchloride siding is fixed in the process of facing to the system of the crate by self-tapping screws or nails along the entire length every 40 centimeters. In this case, the fastening occurs to each intersecting profile of the frame system. However, for the edging of this finishing material and docking along the length, you should use special profiles for siding, or, as they are also called, trims. For each specific case, their sizes and specific configuration of these elements are provided.

Initial profile

If you are thinking about how to expose a profile under siding, then first you need to understand the variety of these elements of the cladding system. Among other things, you can distinguish the starting or the initial profile, which should be below the crate, if it is a question of horizontal installation of panels. If the installation is done vertically, then the bar must be on the side where the surface finish begins, namely from the pediment, the wall or the eaves. Thus, this element will be on the right or on the left.

If you are faced with the question of how to expose a profile under siding, it is important to remember that, unlike the panel, the installation of the described elements of the system is carried out as rigidly as possible. Fasteners, namely self-tapping screws or nails, should press the bar as tightly as possible. Elements of the lath are hooks for the panel. The initial bar has a length that is typically 3.66 millimeters. At the facing of the building, the color of the starting profile will not make any difference, as it will later be hidden by the trim panel. If we take into account the fact that this is a rather thin profile, the technology involves screwing not onto individual racks of the dredging system, but on a plane.

If you decide to choose a proprietary subsystem of ventilated facade, which serves as a frame for cladding, then there is a horizontal profile, whereas in self-made structures a UD profile is added, but in the wooden crate there is a perforated corner.

Setting of the angular profile

Before exposing the profile under the siding, you need to take into account that this system involves many elements, including angular profiles. They are used to decorate the outer corners and to join the panels together. To install such slats, the self-carrying end rails of the slinging system must be mounted in steps of 10 centimeters from the corner of the building. It is important to pay special attention to the perforated mounting edge of this profile, which lies on a plane located at the same distance from the corner.

Before starting work, you need to decide which profile to choose for the siding. It must necessarily be made of the same material as the panels. The profiles described above need not necessarily have a smooth surface, they can repeat the decoration ornament. Thus, in the collections of the socle siding, the profiles are made with an imitation of a brick or natural stone, namely, that figure that this batch possesses. Despite the fact that the corner bar with the imitation of bricks can be used for siding, which looks like natural stone, in the end everything will depend on the designer's decision.

The distance between the profiles under the siding is usually determined by the width of the trim. For any panels, the profiling of the connecting bars will be the same. Thus, the profile under the log will be the same as under the "shipboard". It should be noted that the finish when heated is expanding, therefore, making the fixation in the profile, you should reduce the length by 10 millimeters. This will eliminate the inflation at the stop, which can cause deformation of the profile and the surface itself.

How to expose an angular profile

If you have wondered about how to expose a profile under siding, you should also take into account the fact that in buildings, in addition to external corners, there may be internal ones. For them, you should use a guide that has a similar value. The master should remember that in the absence of it for finishing the internal profile, you can use a pair of J-trim-slats, which are mounted on separate planes. To fix the internal angular profile, it is necessary to make a 10-centimeter indentation of the load-bearing elements of the grid from the corner, then the fastening part of the strip will coincide with the frame. The profiled internal angle bar has the same length as the outer one, this figure is equal to 3.05 meters.

We expose the J-TRIM profile

To find out how to mount the profile under siding, you can by reading this article. There is another element that is used in the inner corners in the process of facing the buildings. He was mentioned above. This profile is intended for cases where only one wall is faced. This element is called edging or ending. In some cases, it is used in place of the edging, it is used instead of the finish or starting line.

Such a profile can be observed during the process of finishing the cornices with siding. The length of the guide in the usual version is 3.66 meters. The technology of the installation remains the same: it will also be necessary to provide a rigid fastening with the help of nails and screws, which are installed in steps of 40 centimeters.

Setting the finish profile

If you do not know how to mount the profile under the siding, you can see one more technology installing the finish line. Its configurations resemble the above-described profile, but this element differs less impressive thickness. He is tasked to keep the finish not on the profile thickness, but on the thickness of PVC.

The finishing bar is able to tighten the final panel quite tightly, but this will not be enough to hold the element, as a strong gust of wind can inadvertently tear the canvas off its seat. In order to exclude such consequences, the finish, refueled in the finish profile, should be additionally strengthened with screws through the lining. It should be noted that the fasteners must be made of stainless steel.

H-profile installation

When a frame is created for siding from a profile, there is a need to install this element. This is necessary for the reason that the wall of construction is most often longer than the panel. It is for their connection that this profile is used. Carrying elements of the crate are located vertically, and in the same direction it is necessary to set this bar.

To fix between the vertical profiles of the frame system, you should strengthen the horizontal ones, observing the step of 50 centimeters. They will be the basis for installing the above-mentioned bar. The fixation of this profile is made using the same technology used to fix the remaining elements.

Features of the installation of the window profile

When the skeleton under the siding of the profile is arranged, there is necessarily a need for using window elements. They are used to close the slopes. These components of the system are like the letter F. The wide part covers the escarpment, but if it turns out to be too large, it can be cut with a construction knife or angle grinder using a ruler.

Fixing of this profile is made for perforated edge by screws or nails, which should be removed from each other by 40 centimeters.

Tips of the master

How to expose corners from the profile under the siding, has been described above, as well as the technology of installing the remaining profile elements. In the article the main profiles that are used for facing the building are considered, but on the market you can find auxiliary slats, the price for which can be very different. For vinyl finishing, use only the vinyl profile. Galvanized steel can only be used for metal panels.

If you are thinking about how to correctly set the profile under the siding, you should pay attention that when installing the finish on the building, it is necessary to fix all the existing profiles. Only after this is allowed to start the installation of panels. Experts recommend using items that belong to the same collection. First, you need to decide which - vinyl or metal - profile under the siding to choose. Each type of material has its own positive and negative features. Metal has a longer service life, but the vinyl profile does not exert pressure on the walls and foundation.

Conclusion

It is important to maintain the distance between the profiles under the siding as closely as possible. Recommendations on the technology were presented above. If they are available for your understanding, then the installation of the panels themselves will not be accompanied by special difficulties.