How to glue the plinth on the ceiling in the corners? Glue for ceiling skirting boards. How to cut a ceiling skirting board

Ceiling baseboard performs a decorative role, so when repairing its gluing should pay special attention. On flat sections this is quite simple, but novice masters are wondering how to glue the skirting on the ceiling in the corners.

What you need to know about sticking the plinth

In order to harmoniously combine the ceiling and walls, it is best to use a plinth. With its help, you can hide the wiring, so the most common fillets are hollow. If it is a question of wide baguettes, then they can hide the backlight, the rays from which will lie soft light on the ceiling. The modern plinth is made of gypsum, stone or wood, as well as polystyrene and polyurethane. For decoration, white moldings are used, but it is not uncommon today and color models. Regardless of which material is the basis, the baguettes have a standard length, which is limited to two meters, so in the process of carrying out their work, they will be joined. To fix skirting boards it is accepted before pasting of wall-paper and coloring of a ceiling. But the greatest difficulty is the fitting of the ceiling skirting in the corners.

Alternative solution

Some, not figuring out how to glue the plinths on the ceiling in the corners, get ready corners, which remains to paste into the corners and dock with the rest of the elements. However, this method has certain disadvantages, which are expressed in a higher cost of these consumable components. There is one more problem. It consists in the fact that not all the apartments have perfectly flat corners. Therefore, sticking out fillets from individual segments is more convenient, since you can independently set the desired angle.

How to cut

Before gluing skirting boards on the ceiling in the corners, it is necessary to prepare not only baguettes, but also the surface, the latter must be cleaned of dust and other contaminants, and also be as dry and smooth as possible. The necessary condition can be achieved at the stage of puttying and priming. Even if the corners are far from perfect, sticking skirting boards can improve the situation for the better.

The first bar is set from the corner that is closest to the entrance. You can cut off the rail using a chair, this is a special device that looks like an inverted letter P. In the sides of this tool, there are slots at the right angles. Between the sidewalls you need to install a plinth, and in the right slot - a hacksaw. Then you can start sawing. If you are thinking about the question of how to glue the plinth on the ceiling in the corners, then in addition to the hacksaw, you should prepare a set of simple tools, namely:

• Goniometer;
• stationery knife;
• pencil;
• Hacksaw for metal;
• Ruler.

Professional pruning with a smooth edge and without burrs can be done with the help of electric jig saw, saber or miter saw. But such tools are not always available in the arsenal of the master. If a hand tool is available, then the skirting must be cut as carefully as possible, since the teeth can crumble or layer the material.

For reference

Before you cut a ceiling skirting, you can make a chair yourself, as it is a very primitive tool. For this, two boards must be used, which are built at the right angle and have a cutout in the right place. If you can make a similar device, then you can cut the material even on weight, pressing the element to the boards. If the work uses foam plastic products, then cut them with a construction knife, the blade of which is preliminarily sharpened.

Glue skirting in the corner

Information on how to cut the ceiling skirting was presented above, but to achieve a positive result it is important to know also the technology of gluing elements. You can connect the plinth in the inner and outer corners, the first is 90 °, but the outer corners are less common. Most often their angle is 270 °. Cut molding for internal and external angles is necessary for the same technology, joining the two bars - left and right. Using a chair for cutting fillets, it must be remembered that the side of the baguette, pressed when cutting corners to the side wall of the instrument, will be placed against the wall by the same side that is pressed against the bottom of the instrument. If it is an internal corner, the lower side will protrude above the top. First, you need to measure the angles between the walls, if they are 90 °, then cut the elements at an angle of 45 °. If the angle is different, then the desired value must be divided into two.

The installation of fillets starts from the corners, afterwards it is possible to work on straight sections. If you decide to use stucco, then to fix it, putty is applied. Before installation, the mounting points are wetted with a primer, this allows to avoid quick drying of the putty and facilitates installation. If you make joints of skirting boards in the corners on the ceiling, you must first distribute the putty with a spatula, trying to create a thin layer. After the skirting board is applied to its place and pressed against the surfaces. From surplus of a mix it is necessary to get rid, and the remained slots fill shpaklevkoj. Remains of the composition are removed with a rag soaked in water. As soon as the putty dries, you can again seal the cracks.

Strengthening the skirting board with glue

Apply the glue composition on the back of the skirting surface, for this you can use a brush. It is permissible not to glue joints of products, and after the fillets are pressed against the wall and ceiling, they must be held for 1 minute. If plastic skirting boards are installed for the ceiling, then it is important at the final stage to wipe the sealant formed between the wall and the plinth space. This applies to the places between the ceiling and the plinth. To carry out such work is necessary around the perimeter of the room, using a rubber spatula.

Types of glue for ceiling skirting

Polyurethane skirting for ceiling can be strengthened to surfaces with the help of polymer mixtures. Such adhesive compounds are developed for each variety of products. The most popular among consumers today are the brands "Titan", "Eco-naset" and "Moment". They have a good astringent ability, they harden in a short time and are able to keep the bonded material immediately after strengthening to the surface. However, if you decide to install a polyurethane plinth for the ceiling using one of these formulations, then you need to understand their characteristics.

For example, adhesives "Titan" and "Eco-naset" have increased gluing abilities and are completely transparent. However, until the mixture is set, the element must be maintained to prevent shear. But the "Moment" grasps immediately, but it is necessary to work with it as carefully as possible to exclude the composition from getting onto the front surface of the plinth. This adhesive composition can only be used in tandem with a mounting gun. As practice shows, the latter option is characterized by a higher cost and expense compared to the above alternatives.

Adhesive for ceiling skirting on a polymer base is applied with the mandatory use of a solvent that allows the mixture to be in a liquid state. But work with such adhesives is necessary only in well-ventilated rooms.

Use of liquid nails

Liquid nails are universal, as they are able to glue almost any material. They can be neopropylene or acrylic. The first variety has a sharp odor and is made on the basis of an organic solvent. It is unsafe for human health, but only until it dries. Before the acrylic variety, neopropylene liquid nails have an advantage, which is expressed in the ability to work in rooms with high humidity and at low temperatures. Acrylic adhesive for ceiling skirting in the form of liquid nails is harmless to human health, but has a faint smell. It is worth remembering that these mixtures are afraid of the effects of low temperatures, and when freezing, the acrylic base is destroyed.

Conclusion

If you decide to use a ceiling skirting during the repair, the inner corner with these elements can be decorated. For cutting the material, you can use a chair, and if you have enough experience in carrying out these jobs, then cutting products can be carried out "by eye".