Sports and FitnessEquipment

Catamarans for fishing under the motor. Catamaran inflatable under the motor

In the shops there are many modifications from polyvinyl chloride. In order to understand this question in more detail, it is necessary to consider specific boats. It is also important to note that they can be done on their own. All this can be learned from the article.

Catamarans for fishing under the engine are distinguished by a rigid base. Frameworks for models are often made of aluminum. On average, the inflatable boat does not exceed 20 kg. In turn, the load capacity parameter is at the level of 300 kg.

The model with own hands

To make catamarans for fishing under the motor by the hands is difficult enough. First of all, a frame is being built. Next, the cylinders are installed on the sides. The skeleton is recommended by many specialists to be made from dural. It is more expedient to choose a small height. On average, the length of the balloon should not be more than 380 cm. For this purpose polyvinyl chloride should be selected for a high density. After installation of cylinders the baller is fastened. To do this, stretches are used. Also need to install a valve to inflate the boat. In the last place put stringer and boards for the seat.

Description of models with flexible locker

Inflatable catamarans (PVC) for a motor with a flexible locker are found quite often. In this case, the boom is of a small thickness. On the market, modifications from polyvinyl chloride are most often presented. The air valve in the devices is at the stringer.

On average, the density of the material does not exceed 800 g. Per sq. M. meter. The advantage of these boats is the possibility of installing large cylinders. Fastening meets the cross type. It is an average catamaran (PVC) for a motor in the vicinity of 55 thousand rubles.

Description of the catamarans with a hard locker

For fishing in shallow water, boats with tight lockers are often used. Most often there are models from polyvinyl chloride. In this case, two supports are installed. Directly the cylinders are fixed on the sides of the stringer. In some cases, it is possible to meet modifications with balloons.

The air valves at them are above the boom. On average, the density of the material does not exceed 700 g. Per sq. M. meter. Supports for models are fixed above the firmware. Rubber bands are often used. It is an average catamaran (inflatable) for a motor with a rigid locker of about 50 thousand rubles.

Features of models on two beams

Modifications to two beams are in great demand. However, it should be borne in mind that only two-seat models are on the market. The index of carrying capacity at them does not exceed 300 kg. Most of the poles are set to a small height. The length of the boat does not exceed 340 cm.

Stringers are often applied with a thickness of about 1.3 mm. The patches of the models are located directly on the cylinders. Double modifications can also be made with flexible lockers. Thus, the nose is considered more secure. Mounting at the catamarans is done through crosses. Buy a boat in the store for 55 thousand rubles.

Catamarans with three beams

Models with three beams are often produced in a four-seater type. Their capacity is about 500 kg. Runduki often used a little stiffness. However, there are modifications to the two pillars. On the market most often sold are catamarans with two cylinders. It is also important to note that the width of the boat does not exceed 130 cm.

Air valves in such models are located near the stringer. The time of filling with air does not exceed 10 minutes. Firmware is most often used for high density. Some boats have a rubber boom. Serve these models are very long. You can buy them at a price of 45 thousand rubles.

Models with low support

Models with low support allow the installation of low-power engines. They are made for two and three cylinders. It is also important to note that the stores have models with stringers. On average, the carrying capacity does not exceed 300 kg. Cylinders are mainly used for small diameter.

Some modifications use baller. Stringers in this case are fixed on a polyvinyl chloride pad. Geeks can be made of rubber. They are different in width. Buy a boat with a low sometimes you can at a price of 50 thousand rubles.

Description of models with high support

Boats with high support are designed to install powerful engines. The length of such models exceeds 400 meters. It is also important to note that the cylinders are of large diameter. The chestnuts are mostly of medium hardness. In the market there are two and three-seat modifications.

The supports are used in this case with an extension. Stringers, as a rule, are installed with a thickness of about 1.4 mm. The density of the material in such modifications is 800 g. Per sq. M. meter. Skeletons are made only from durali. You can buy boats in stores for 60 thousand rubles.

Taimir catamarans

These catamarans are very popular. In this case, the payload index is 450 kg. Geeks in the model are used with overlays. The strips are placed on cylinders. The total length of the catamaran does not exceed 350 cm. Stretching is installed on the sides. Firmware is used dense, paddles are included in the standard kit.

It is also important to note that the fastening of the boat is carried out through the crossings. The density of the material is 780 g. Per sq. M. meter. Buy this catamaran at a price of 56 thousand rubles.

Models of "Rotan"

These catamarans for fishing under the motor "Rotan" are sold with a flexible locker. In this case there are four places. The support is located a short distance from the frame. The total weight of the catamaran does not exceed 22 kg. Firmware is used medium density.

The patches of the models are located at the bottom of the cylinders. It is also important to note that these modifications use baller. The stringer is made of rubber, and its thickness is 1.4 mm. Buy these catamarans in stores at a price of 45 thousand rubles.

Description of the catamarans "Delta 300"

These catamarans for fishing under the motor are made with rigid lockers. The main advantage of the boat is considered to be strong supports. The indicator of load capacity fluctuates around 500 kg. This catamaran is calculated for four passengers. To protect the bow of the boat used geeks. They are made of rubber, they are flexible.

In the back of the catamaran there is an extension with firmware. Baller is applied with a wrap. The standard set includes oars. The density of the carcass material is exactly 700 g. Per sq. M. meter. The width of the balloon is 46 cm. The carcass mounts are crossed. Buy a model can be for 45 thousand rubles.

Features of models "Delta 350"

These catamarans for fishing under the engine are characterized by a high density of material. The specified parameter averages 560 g. Per sq. M. meter. Made this boat with two beams. They are installed next to the supports. For the seat there are strong racks. This catamaran is calculated for four passengers. It is also important to note that this model has a durable boom. It is made of polyvinyl chloride. Stretch marks in the model are installed over the beams.

Directly the stringer is used with a small thickness. The ballerin in the presented catamaran is absent. The standard set includes oars. In total, the device uses one air valve. Dural is not applied to this model. Also the big diameter of cylinders at a level of 46 cm deserves attention. Buy this catamaran for 47 thousand rubles.

Catamarans "Delta 380"

These catamarans for fishing under the motor to many consumers like because of tight cylinders. Their diameter is 50 cm. The density of the material is 560 g. Per sq. M. meter. Geek in the model is on the cylinders. It is also important to note that it uses rubber panels to protect the coating. Baller is applied with a wrap.

The bow of the catamaran is protected by a stringer. Oars are included in the standard kit. Fastening of the frame takes place through the crossings. The width of this catamaran is 156 cm. The support of the model is not high, so you can install a low-power motor. Buy this catamaran for 52 thousand rubles.

Models "Buster"

These catamarans (PVC) under the motor for fishing are in great demand. However, it is important to note that this model can accommodate only four people. Geek in this case is not provided. The strips are made of rubber. Stretching in the presented catamaran is located on cylinders.

The total length of the model is 430 cm. It uses a stringer of small thickness. The average density of the material is 780 g. Per sq. M. meter. In total, the catamaran has two air valves. Buy a model can be for 57 thousand rubles.

Similar articles

 

 

 

 

Trending Now

 

 

 

 

Newest

Copyright © 2018 en.unansea.com. Theme powered by WordPress.