The stove from the gas cylinder with your own hands: photo and instruction

With the onset of cold weather, the issue of thermal insulation becomes topical. Especially it is important for the premises that you visit from time to time. This includes garages, workshops and utility rooms, where it is not advisable to install a stationary system. In some cases, this is completely impossible, but if you can not do without heating, the stove can be made from a gas cylinder with your own hands.

It is recommended to use one of two options, the first one is to create a system on electricity, while the second one is to use a solid fuel. Among the latter can be attributed burzhuyku, which can create even an inexperienced home master. As the main element of this design will protrude the body, it will need to do two holes through which the inside is to lay fuel. The system must have an ashtray and a chimney. The last element quite often connects to a compartment where ash is collected. For easier cleaning of the furnace it is necessary to equip in this place one more door.

Council of the master for the arrangement of the chimney

If the stove is to be manufactured from the gas cylinder with your own hands, the chimney should not be laid along a short path, with most of the heat going to the outside. This approach can not be called rational, therefore, experts advise to equip a broken-line pipe. So you can increase the efficiency of the heater. In the role of fuel, you can use coal, firewood, old clothes and even household rubbish. Attracts the craftsmen of the bourgeois also with its simplicity, and also versatility, because with its help it is possible not only to heat the premises, but also to prepare food.

Preparation for work

If the stove is to be performed from the gas cylinder with your own hands, you must first prepare the container for operation. This procedure should be made necessarily, otherwise the gas can explode from the impact of the spark that occurs during the cutting process. The master must unscrew the valve and allow the gas to escape. The container should be turned over after this and drain the condensate. Its smell can not be called pleasant, so it is worth collecting the remains in the vessel.

The cylinder is installed vertically and filled with water, this will remove the gas residues inside, after the capacity is turned on its side, which will drain the liquid, now the can can be started to be cut. Before starting work it is important to determine how the burzhuka will be located: horizontally or vertically.

The first version of the furnace

The stove from a gas cylinder can be made on the basis of a horizontal design with own hands on wood. Initially, it will be necessary to cut off the upper part of the balloon, and after installing the grate inside . It should be made from reinforcement, placing the elements with a snake. Installation of the grate is accompanied by welding, after which it is possible to tackle the front part of the furnace. On the steel sheet you need to outline the contour of the circle, the diameter of which will be equal to the outer contour of the cylinder. Then the detail is cut out, and inside the circle two rectangular holes are marked. The first is necessary for supply of fuel, and the second will act as an ashtray.

Main Stage

If you will be making a stove from a gas cylinder with your own hands, you can view the photo in the article. With the help of a grinder or a chisel, it is necessary to cut out the intended holes, which were discussed above. To the finished lid should be strengthened by welding the veil and install the doors on them. The latter should be sealed with an asbestos-cement cord. On this, we can assume that the front of the furnace is ready, you can proceed to work on the rear. This stage provides for the installation of a chimney, for which it is necessary to make a hole with a size equal to the diameter of the pipe. It installs a chimney of the desired shape, which should be made of a thick-walled pipe.

Making a vertical oven

If you will make a stove from a gas cylinder with your own hands, a step-by-step instruction will be useful to you. If you need a vertical design, you can use one of two methods. The first provides an impressive amount of work, they are associated with the cutting, but the installation phase will be accompanied by less complexity. If you decide to choose this method, then using Bolgar you need to remove the container from the top. The second method will save time, electrodes and forces, but it can not be called convenient. In this case, the upper part must be furnished in place.

Whichever method you choose, in front of it you will need to cut out a big hole in the furnace. Bottom is a smaller in size clearance for cleaning and blowing. When a stove is manufactured from a gas cylinder with its own hands for prolonged burning, the same technology is used. Holes can be of arbitrary size. At the next stage, grids are prepared for installation work, in the first case, these elements are lowered through the top, but the second technology does not provide the possibility to install the grates in such a way, it will be necessary to enter them from below, which is extremely inconvenient.

Ensuring airtightness and installing a chimney

If a stove-burger is to be manufactured by hand from a gas cylinder, then the next step is to install air curtains, and then weld them to the holes. The door is pasted with an asbestos-cement cord, which will guarantee perfect tightness. Do not forget that there are still holes to be made for the chimney. Through the hole that is located in the top cover, waste gases will be discharged and oxygen will be supplied. Its dimensions should correspond to the diameter of the pipe. You can also provide a sidestream smoke outlet. In this case, you need to work on the side of the case. Experts in some cases advise to equip the knee, but you can make a conclusion quite straightforward. If the balloon has lost the upper part, then the chimney can be installed from above.

Furnace production on the working

The stove from the gas cylinder with its own hands on the working can be easily executed. Its design is not difficult. You can also use sheet metal, for this you need to make two combustion chambers, one of which is attached legs. Two compartments are connected by a pipe to the holes, and the installation of this element is carried out on the upper chamber. All these works involve the use of a welding machine and the availability of certain skills from the master. If you want to do less time, then you can use a gas cylinder. It has thick walls and will provide fire safety. Air supply to one of the chambers must be made adjustable, for this purpose a damper is installed, which, if necessary, can be opened slightly. The camera, where the waste oil will be fed, should be made folding, so you can clean it. The chimney is located vertically, inclined and horizontal sections should not be. For a good draft, the chimney must be selected in such a way that its length is four meters or more.

Technology of work

When a stove is manufactured from a gas cylinder on the working line, it is necessary for the vessel to cut the lower and upper parts, the halves obtained will form the basis of the collapsible combustion chamber. The lower part should be equipped with metal legs, and in the upper part a hole is made, into which a pipe with an adjustment plate is installed. In the central part there must be an opening to which a pipe connecting the two compartments is welded. In the connecting element, it is necessary to make openings for air. The middle part of the tank will go to the manufacture of a secondary combustion chamber, which is attached to the connecting pipe. The final stage will be the manufacture and installation of a chimney, which can be problematic due to the impressive length of the component.

Tips for the manufacture and operation of the kiln for working

If the stove is to be performed from the gas cylinder with your own hands, then you should choose the dimensions yourself, these parameters are not so important because the design can be easily adjusted. In garages and workshops, as well as utility rooms, in rare cases there are perfectly flat floors. In order to install the oven correctly and ensure its fire safety, it is necessary to make the feet adjustable in height.

If you notice that the oil splashes out of the combustion chamber, it is necessary to stop the device, wait for the complete cooling of the surfaces and to pour out the fuel. It should not be more than 2/3 in the compartment. If the refining has begun to boil, it is necessary to reduce the air supply by using an adjusting flap. For a sufficiently intense thrust, the tank and chimney must be cleaned periodically. Remove the soot from the upper part of the product can be the method of tapping.

Conclusion

The manufacture and operation of such a heater is very cheap. This is also due to the fact that waste oil can be easily purchased or taken almost free of charge at the service station. If you are a car enthusiast, then for the oil you can have a special container, in which you will collect the workings obtained in the warm season.