Restoration of the bath with your own hands. Bath restoration with acrylic (reviews)

For any person, the bathroom is one of the favorite places. After all, where else you can lie in warm water relaxing, forgetting about the problems and fuss ... However, the coating of the bath itself eventually wears out and becomes yellow, forming spots. Now, the restoration of bathtubs is widely used, people's feedback on this process is the most enthusiastic. After all, there are many materials that update the old coating. The view of any bath becomes as if it had just been bought and installed.

Ways to restore the bathroom coating

To date, there are three ways to update the old bathroom cover:

• Use a brush to paint over damaged areas;
• Make an acrylic liner;
• Method of filling bath.

Restoration of bath coating using a brush and enamel

So, let's start with the first method, it can be called "the restoration of the bath enamel," so it will be more accurate. For the whole procedure we need:

• Brush, preferably wide and with which hairs do not drop out;
• Sandpaper waterproof on a fabric basis;
• Some powder cleaning;
• Respiratory mask.

Armed with all this, you can start work. In the hardware store you need to buy a bath repair kit. It includes paint on the basis of epoxy resin, as well as a thickener or hardener in a separate container. It is necessary to carefully read the instruction, which states in which proportions to mix the two components. When the required composition is ready, you can begin the operation "restoration of the bath with your own hands."

We prepare the bath for the restoration of the surface

The bath is washed with a cleaning powder to remove contaminants and bacteria that may not give a full grasp to the new enamel.

Then it follows, without flushing the powder, to clean the area with sandpaper, which are to be restored. The chips must be cleaned to the metal, so that the surface becomes even and without bumps.

Further, it is washed from the particles of waste enamel and powder.

After that, fill the bath with hot water, and then after ten minutes, lower it. This is to ensure that the surface is well warmed up for the rapid drying of moisture.

It is necessary to put the bags on a mixer and a shower to prevent accidental water ingress onto the uneven enamel, because the restoration of the bath with its own hands does not tolerate a mistake.

If there are large chips, then to eliminate them, automotive polyester putty is used. When it dries, you need to clean it with sandpaper, then remove the formed dust with a vacuum cleaner and a rag.

Covering with new enamel prepared places

It is necessary to mix the contents of the two containers by pouring the thickener into the enamel. Everything needs to be done quickly, because an hour after mixing the composition it will not be suitable. Next, using a brush, the enamel is applied to the finished surfaces. Everything needs to be carefully leveled. Then, without waiting for drying, you can cover with a second layer. These actions need to be done in 50 minutes. If there is no certainty that the restoration of the bath enamel will take place during this time, it is better not to mix everything at once, but divide by half.

Safety precautions

Mix all ingredients in a respiratory mask, because these substances are toxic. Wear protective gloves.

Method of restoration of the bath with acrylic liner

Using a sealant, you need to glue to the inner surface of the bath liner from acrylic. This method of restoring the coating is not suitable for most domestic craftsmen. All because to find these very inserts is almost impossible in ordinary stores. They are sold mainly to large enterprises or masters who are engaged in plumbing.

The method of filling bath and what people say about it

Now we will describe how the bath is restored with acrylic. Reviews of this method say that it is ideal for restoring the coating yourself. Many people, after reading about all the intricacies of this reception on the forums, decided to do everything themselves. Other materials for restoration are often toxic, so they are inconvenient to use at home. A method with the installation of an acrylic liner is also not suitable for the reasons described above. It remains to apply a fill with liquid acrylic. In this way it is really easiest to carry out restoration, so it is used by both professionals and home craftsmen who do it for the first time in their life. This method is ideal when restoring acrylic bathtubs, cast iron or steel.

Tools

To implement the whole process, we need:

• Acrylic is liquid, its other name is liquid;
• Spatula soft, elastic;
• Drill and grinding wheels;
• Acetone, to degrease the surface;
• A respirator to protect the lungs from dust;
• Stick to stir the enamel, thickener, knife, rubber gloves, rags, scotch tape and newspaper.

Preparing the bath

We disassemble the holes for draining and overflow. This must be done for easy operation. If the cast-iron bath is restored by hand, especially when it is an old sample, then it may be problematic to remove the sink because the carving could rust. Then the body kit will have to be dismantled.

When the drain and overflow are removed from the hole, you can start polishing the surface. Do it with a special machine, a drill with attachments, or if there are no such units, you can use sandpaper. Often people underestimate this part of the work, neglecting it, but it's worth to take it seriously, because it depends on it how the liquid acrylic glues together with the coating. And the better everything grapples, the longer the shape of the bath will remain sparkling and snow-white. When grinding, you must always wear a respirator, it protects against the ingress of small particles and dust into the lungs.

The restoration of the cast-iron bath continues. Now you need to remove all the dust from the grinding. This is done with a lint-free cloth, you can also use a vacuum cleaner without a nozzle. After that, the surface is degreased with acetone. They moisten a piece of cloth and rub the bath. It should be ensured that there are no fragments of the old coating or villi on the surface. Any remaining even the smallest trash can later lead to marriage. Instead of acetone, you can use any cleaning powder.

We prepare liquid acrylic for use

Restoration of the baths with a glass (so-called liquid acrylic) is done carefully, so that its snow-white color can not get dirt or anything else. Open the jar with a clean screwdriver or knife. Stir liquid acrylic need, according to the instructions, a wooden stick slowly circular motions. Do not use a drill with a nozzle for this. This can lead to the formation of air bubbles in the mixture. So that acrylic was homogeneous, you need to mix it slowly, adding a little hardener. And so it is necessary to continue for 10-12 minutes, until everything becomes homogeneous.

It is very important that the restoration of the bath with liquid acrylic is carried out from the beginning of the mixing of the future coating to the complete end of the work in an hour and a half. After all, only during this time the composition will be suitable for use. If you stay longer, it will start to freeze and become unsuitable for further manipulation. So it's worthwhile to think everything over for more precise and quick actions.

We prepare the container for coating the bathroom with liquid acrylic

To evenly cover the entire surface, a convenient plastic can be used, it can be made from a bottle containing a hardener. You need to trim its top, but in such a way that one corner is higher than the others. It will be like a tip of a teapot.

Protection of the floor and other unwanted parts for painting

It is necessary to take newspapers or a large piece of polyethylene and close the floor. Using adhesive tape, glue all other surfaces where the mixture should not get. After the restoration of the bath with liquid acrylic may not be very clean, so it's worth reinsuring. In addition, should be put on mixer bags, to be safe from getting water on acrylic when pouring the bath. Also, you need to place a container under the hole of the sink, into which the mixture will flow.

The process of pouring liquid acrylic

So, the plastic jar is ready, you need to prepare a flexible spatula to evenly distribute the liquid acrylic on the entire surface. When everything is at hand, the restoration of the bath with his hands comes to the main part of it - the pouring. Pour acrylic into the jar from the thickener and start pouring on the top of the bath so that the material drains down. Do this carefully, trying to grab as large a surface as possible. This is done until they are combined with the beginning of the pouring. Then, the restoration of the bath with their own hands goes into the phase of homogeneous distribution of acrylic on the surface.

After that, you need to smear and add fill to parts of the surface, where it is not yet. Everything is done from the same place where you started, only a little lower. With a spatula, the threads are leveled so that they cover the entire surface horizontally. Now the material will begin to accumulate at the bottom of the bath, this is normal. When all the walls and top are evenly covered, take a rubber spatula or roller. They are used to level the bottom and walls. This is how the restoration of acrylic baths is carried out, this is a universal method.

After the entire surface is covered with a uniform layer, it is worthwhile to check it all. To do this, use a flashlight, its light directed, and if there are flaws, they will immediately be visible. In basic lighting, you can overlook, because it is more diffuse. The method described here with liquid acrylic is the best option for home use, after all, such a restoration of bathtubs reviews has received approval from both professionals and home masters. Therefore, it is worth choosing from among all the listed ones.