How to start a car with a pusher. How to start a car with a pusher on the machine

The problem with a discharged battery is familiar to every car owner. And often this happens on the day when you can not do without a car. In this case, the question arises as to how to start a car with a pusher. Today, we'll look at how to do it right.

rules

To begin with, note that simply because the machine does not start with a pusher. This can only be done if your braking system is in an absolutely working condition. Also you will need to find another car that will serve as a tug. If such a number is not there, physical strength will do. Ask friends or neighbors to push your car. This is enough for 2-3 people. Before this, you must specify the stop signals that can be sent from the window or horn.

If you have a carburetor, before starting it is also necessary to pump fuel with the accelerator pedal. For this it is enough to make 2-3 clicks on the floor. If you have an injector car, do not do such manipulations.

Exhaust pipe condition

Before you start the car with a pusher, pay attention to other points. If you encounter this problem in the winter, be sure to check the condition of the exhaust pipe. It should not be clogged with ice or snow. Ice is a sign of frozen condensate. In this case, you will not be able to start the engine. Although you can try it - this will not lead to the failure of the belt and other important elements of the car. What does it take to do this? To do this, remove the battery and take it to a warm room. Better immediately put it on the battery. But do not forget that the battery should not be very hot. Therefore, we place it at a small distance from the battery, and not on its surface. The preheating will take about 2-3 hours. After that, put the battery back in the car and start up.

If the pipe just formed snow, we clean it and hope for a successful launch of the ICE. Nothing to warm up in this case is not necessary.

How to start a car with a "mechanic"?

If all the above rules are met, you can start the start. So, how to start a car with a pusher (injector)? First, insert the key into the ignition and turn it. Then we turn on the "neutral" and give the conditional command to people so that they start pushing you, or the driver of the second car, to start pulling.

When your car has started to move a little, it is necessary to squeeze out the clutch and turn on the second gear. After this, there must be a push, and the engine will then start.

Again squeeze the clutch and, if necessary, braked. At the same time, the transmission lever is moved to the neutral position. In order to avoid trouble, all the above manipulations should be performed as clearly and quickly as possible.

Everything, our engine started. Now you can give the appropriate signal to the tug or people pushing from behind. But in order for the engine to warm up normally and not to stop again, let it run for another 15 minutes.

What if the car is started from the pusher badly? As practice shows, sometimes motorists do not manage to start a car from the first time. In this case, it is necessary to repeat all the above steps again. This is done until the machine starts. After starting, do not forget to recharge the battery so that you do not have to push the car again.

How to start a car with a pusher on the "machine"?

Almost all motorists say that this method of starting the engine can not be used on an automatic transmission. And there are objective reasons for this. The fact is that the automatic transmission has a slightly different operating principle.

The essence of starting the car from the pusher is the ability to transfer torque from the wheels through the transmission to the engine. In cars with an "automatic" with the engine off, the gearbox also does not work, since the oil pan pumps the liquid only when the engine is running. In other words, there is no connection between the wheels and the engine through the box on the muffled car. Accordingly, when towing the vehicle, the torque forces will not be transmitted to the motor, and the piston group will remain stationary. However, some craftsmen start the car even with such a transmission.

How to start a car with a pusher with a box machine? To start the engine, you need to do the following:

1. In tow, the car accelerates to 50 kilometers per hour. It's clear, one physical strength of a neighbor is not limited to - you have to look for another car.
2. Having traveled at this speed for several minutes, we translate the gearbox lever from the neutral position to the "drive" mode (on the gearbox knob it is indicated by the symbol D).

Starting the engine after this hardly anyone can guarantee, and in practice most of such experimenters transmission simply fails. In general, it's not for nothing that motorists say that it's impossible to start a car with a pusher on an automatic transmission. Therefore, in order to avoid expensive repairs that "take" from you several hundred thousand rubles, it is better not to use this method and in extreme cases take a taxi.

note

It is worth noting that starting a car from a pusher is not safe even for a manual transmission. The fact is that after such actions you risk cutting off the timing belt. But this is fraught with expensive engine repairs. Therefore, if you have a car with a "mechanics", use this method of starting the engine only in extreme cases, and in the case of the "automatic" do not use it at all.

Conclusion

So, we found out how to start a car with a pusher and what dangers await motorists with an automatic transmission after a similar engine start. Finally, we note that for a better start in the winter, it is better to take a battery every day after a trip in the evening and put it in a warm room for the night.