How to make a gun for underwater hunting with your own hands

For underwater hunting, buyers are offered a lot of guns. By design, they are very different. The most common are harpoon modifications. However, traumatic models that have large muzzle energy are also on the market.

If you engage in self-assembly of weapons for scuba diving, it is more appropriate to consider harpoon modifications. Materials for them can be used the most diverse. It should also be borne in mind that the slaughter power of homemade weapons depends on the parts used. To independently assemble a model, you need to consider the most popular devices.

Double-skid model

With a double slider how to make the gun for spearfishing? Answering this question, one should first of all think about preparing the pipe. Its length should be at least 12 cm, and the thickness - about 4.4 cm. After its grinding it is necessary to make a channel (drawing of a gun for spearfishing is shown below). It is cut, as a rule, with a width of no more than 0.5 cm. All this is necessary to place the ramrod. After that, the slide is attached directly. The piston for it must be selected wide.

In order to fix the tube, you can use a hook. The clip in this case is suitable for wood. However, it is possible to paste an overlay on it. Then it is important to attach the sear to the rifle. Only after this, it is possible to install a fighting spring. At least it should be 3.5 cm in diameter. Winding for such models is rarely used. Lin with the trigger is installed last.

Hawaiian weapons with metal shoes

Do with the metal shoes Hawaiian shotgun for underwater hunting with their own hands can be no problem. For this, it is standard to prepare a pipe about 12 cm long. Its edges can easily be turned on any machine. After that, the pads are already packed. From the front, they should be installed at a distance of 2 cm from the edge. In this case, they are attached to the posterior region 2 cm further. All this is necessary in order to fix the barrel on the cage.

However, before that many experts advise to cut a channel on the edge of the pipe. The whisper in the gun can only be installed after the lining. Then it is important to make the winding. After that, the line in the gun will be held fairly tightly. The next step is the ramrod. The trigger can be used from any machine. Compensators in this case do not apply.

Shotgun with two springs

This type of making a gun for underwater hunting with their own hands is quite difficult. In this situation, the clip needs to be wide. However, the work should be started as standard with a pipe search for the trunk. After that, it is possible to connect the sear and the clip. Many experts also advise making a winding on the edge of the trunk.

The overlays are used if desired. The battle springs must be attached directly to the axis. At the same time, they should not touch the line. After fixing the war springs, you can proceed to install the feeder. In this case, the slide should be located near the holder. You can use the winding for this. Some also prefer a latch, but you can consider the option with pads.

Pneumatic model with safety catch

You can assemble the pneumatic underwater gun with your own hands for hunting only if you have parts from the machine at hand. First of all, the barrel is removed. In this case, the clip is attached from the bottom with an indent of about 4 cm. Next, you need to install the sear. Compensators are not installed in all cases. In this situation, much depends on the type of fuse. The ramrod must be fixed at the base of the clip near the gun. The safety lock is mounted on the side of the line. It is necessary to look after the feeder. When changing the position, it should not touch the fuse ring.

Device with rectangular feeder

The device of a speargun with a rectangular feeder resembles a modification with a latch. First of all, it is necessary to select a pipe for the model. The thickness of its minimum should be 10 cm. After this, it is necessary to proceed to the cutout of the tubule. The thickness of it should be equal to a minimum of 0.6 cm. Then there is the possibility of making an overlay. The clip in this case is better to install after the sear.

The fuse is used if desired. Further, to make a gun for underwater hunting with their own hands, a rather dense winding is done. All this is necessary so that the return is not great. The axis for weapons is most often selected steel type. Sheptalo can be used aluminum. Compensators for the model fit a variety. The feeder at the end of the work must be carefully sharpened. He should not touch the door.

Device with trapezoidal feeder

With trapezoidal feeder how to make a gun for spearfishing? To assemble such a modification, it is necessary to start with a standard work from the logging. To do this, you can use a conventional pipe with a diameter of about 5.5 mm. The compensator should be set more appropriately after the clip. In this case, the fighting spring needs to be selected with a diameter of about 2.3 cm. The feeder is most often used plastic. In order to secure it securely, it is necessary to use the latch. After this, the trigger mechanism is installed. To borrow it best from a pistol. If the fighting spring is set quite large, then at the bottom it is possible to put a shoe.

Using plastic slides

With plastic skid how to make a gun for spearfishing? First of all, you need to select a good clip for this. In this case, the trunk can be made from a pipe. Its length should be at least 80 cm. The lining for the trunk can be used rubber. The fighting spring on the weapon is installed only after the sear. First of all, the edges of the lining must be carefully cleaned for sealing.

It is also important to take care of the winding. In some cases, it is made of aluminum wire. Further, to make a gun for underwater hunting with their own hands, a small line is installed. Polozok with it should not touch. The feeder is installed above the fuse. In this case, the trigger mechanism is best used in the pneumatic gun.

Application of hollow ramrods

With a hollow ramrod, a spearfishing shotgun with your own hands (the drawings are shown below) can be made using a conventional pipe. Lining for her used most often rubber. In this case, the holder is selected depending on the diameter of the pipe. In the first place, a whisper is set. To make a gun for spearfishing with your own hands, then you need to fix the fighting spring. In some cases, it is fixed on a small hook.

Winding in this case is most often used aluminum type. In this case, the sealing of the weapon depends on the type of the line. Its width should be at least 3.5 cm. In this case, you can hope to overlap the sear. Compensators in such devices are used quite often. The trigger can be used from a traumatic gun. In this case, the latch should be L-shaped. Pads at the end of the work must be selected very carefully. The ramrod is installed only after fixing the clamp.

Arms on the compensator

Collect a compensator for a gun for underwater hunting their own hands in our time is quite difficult. However, if there are details from a traumatic gun at hand, everything becomes much easier. First of all, you need to select a large shoe. Its width should be at least 6.5 mm. The channel should be made on it about 2.3 mm. At the same time it is necessary to fasten the whisper on an aluminum winding. At the edge of the trunk, you should fix the hook. To install the fuse, you need to fix the cage. Its width should be at least 4.5 cm. The ramrod will in this case fit hollow.

Lin for weapons should be chosen rather long. Due to this, the compensator can be installed at its base. The feeder must be at the clip. It should also be taken into account that the compensator must not touch the trigger mechanism. The latch should be about 2 cm away from it. Thus, when the fuse is switched on, the compensator will not overlap.

The solid line model

Models with a continuous line are today considered to be the most common. They differ in their compactness. Also it should be taken into account that the wide whisper of the models will not be established. In this case, the clips fit a variety. The assembly of the gun in this case must begin with the barrel. The screws must be fastened both from the front and from the rear. After this, the clip is installed.

If you make it yourself, you should calculate the length of the sear. It is also important to consider that the edges of the clip must be carefully sharpened. This can be done using a file. After this, the line is installed directly. Then you can proceed to the fuse. Lastly, the ramrod and trigger are mounted. When the capacitor is standing, then a fighting spring is set.

Using aluminum winding

A homemade speargun with an aluminum winding can be found quite often. Sealing such a winding provides a fairly high quality. Begin the assembly of weapons as standard can be from the trunk. In this case, it is more expedient to select a small width. Thus, the winding will lie more heapy. Sheptalo for weapons is better to pick up on three cloves. In this case, the fuse is selected separately.

Much in this situation depends on the size of the line. Compensator must be installed last. In addition, it is important to pay attention to the trigger mechanism. It is difficult to manufacture it independently. Given this, it is more appropriate to use parts from an air gun.

Weapons with double lock

To date, these modifications are rare. In this case, the problem is that the fuse for the lock is required T-shaped. To get it in our time is quite difficult. It should also be borne in mind that the trigger must be used from a pneumatic gun. His teeth are small, fuse does not hurt.

Model with overlay

Models with overlays are the most common. With regard to sealing, they are today considered to be the best. Begin the assembly of weapons from the preparation of the barrel. In this case the clip is attached only after the sear. The lining should be fixed directly to the glue. Its thickness should be at least 2.2 mm. If the ramrod in the model is used rather long, then the lining should be stretched to the holder. In the end, it remains only to fix the latch on the trunk.

The model with continuous winding

To make a model with a continuous winding it is possible, if in advance to prepare a pipe with a wide clip. Many people for this purpose have been advised to use three denticles for this purpose. Install the clip must be very carefully. In width, it should converge with the line. After fixing it, you can proceed directly to the winding. At the same time, it should not be applied to the ramrod.

After completion of work, it is possible to do the compensator. The feeder is then attached directly to the coil spring. Many experts in this situation advise using L-shaped latches. At the end of the job, it only remains to fix the trigger, which can be removed from any rifle.