How to connect ByFly WiFi. Connecting ByFly WiFi and setting up

Usually WiFi ByFly connection does not cause any special difficulties. However, some users have difficulties with configuring the modem or router. About how to connect ByFly WiFi, then we'll talk. The questions proposed for consideration are standard, and the popular modification of the "Promsvyaz-M200" will be selected as the considered model of the router. For ByFly, modem setup is not the most complicated operation. But first things first.

How to connect ByFly WiFi: the necessary primary conditions

First of all, when concluding a contract for the provision of services, pay attention to the indication in it of specific data like login and password that will be used when connecting to the network.

The second point is connected with the equipment received from the provider. First you just need to connect the router to the computer and install the drivers for it. If the operating system did not install in the automatic mode, you need to use a special disk, which has all the necessary software. It should be present in the kit when buying the main equipment.

Finally, you should make sure that there is a wireless WiFi module on the laptop or a desktop computer, the corresponding drivers are installed for it, and it works in the normal mode. You understand that without the presence of such a module in the system and the drivers installed for it, there is no need to talk about wireless connection. Separately, note that on some notebook models, connection can be made by a special switch on the side panels, keyboard shortcuts using FN or some other method. This is very important, since further consideration of the issue of Internet connection without this does not make sense.

Checking the wiring diagram

As a rule, in connection with how to connect ByFly WiFi, the connection of modules should not be a problem either. For this purpose, a standard cable with RJ-45 connectors, also called a patch cord, is used.

How to configure WiFi on ByFly? It's simple. The main device is connected to the provider's cable, but to configure the device itself, you must use a direct connection to the terminal initially. This is only necessary at the first stage of setting the necessary parameter values, and in the future it will not be necessary. After saving the settings, they will be applied to the entire viral network.

Setting up WiFi on ByFly "Promsvyaz"

So, the circuit is turned on and running. The first step in solving the problem of how to configure WiFi on ByFly will be to enter the interface of the router, which, in fact, will be responsible for providing communication.

To do this, we use any web browser installed in the system (though the same Internet Explorer or Edge, which is present in Windows 10). From the software of this type nothing much does not depend.

Access to the interface

Now for ByFly WiFi-modem setup will be performed according to the below diagram. In the address bar, register 192.168.1.1. In the standard configuration, admin is used as the login and password. If the router for any reason gives an error, the settings can be reset by pressing the corresponding button on the back of the device or disconnecting it from the mains for about 10-15 seconds.

Some users advise to withstand a longer interval (about 15 minutes), but I do not think this is necessary.

Now, in the question of how to configure WiFi on ByFly, the most basic begins. In the interface the router entered. Use the Interface Setup tab, where you initially need to set PPPoE (ISP field) on the connection type.

, сводится к следующему: нужно будет ввести логин и пароль, которые были указаны в договоре. At this stage, the question of how to configure WiFi on ByFly is as follows: you will need to enter the login and password that were specified in the contract. Next, which is very important, in the Bridge Inetrface field, you need to activate (mark the item Activated).

Similar actions are performed for the Default Route line with the on-demand reconnection setting at 30 minutes.

Save the changes and go to the Wireless tab. Now the setting of WiFi ByFly ("Promsvyaz" -modem is taken simply as an example) means entering the following parameters:

• Activate Access Point;
• For Broadcast SSID, set to Yes;
• In the SSID network name field, enter any arbitrary name;
• In the authentication type, select PSK2-WPA;
• In the Pre-shared key field, enter the invented access password for the connection;
• Save the changes by clicking the Save button.

System settings

In theory, after all the operations done, both the connection and the network must be earned. But it also happens that the operating system does not automatically accept the settings. In this case, the question of how to connect ByFly WiFi will be reduced to changing some parameters of the network adapter.

To do this, you need to log in to the network and sharing control section, which is located in the standard "Control Panel" (you can also call it using the ncpa.cpl command from the "Run" console).

Here you need to select the required network connection and go to the section to change the properties of the network adapter. In the properties of the network, choose the IPv4 protocol settings (as a rule, the fourth version is used in the basic connection variant, and not the sixth one).

For the gateway, set 192.168.1.1, and for your own internal address, change the last digit to 2. Obtaining DNS addresses, if everything works, you can leave it on automatically receiving settings.

What should I do if DNS does not work?

But what if the connection does not work even if the settings are automatically set? In most cases, the problem of how to connect ByFly WiFi can be solved by setting the DNS server addresses manually.

This refers to the specification of parameters from the configuration of quadruples and eights based on free Google services. Do not like this option? Use the Yandex settings or simply perform a full reset with clearing the DNS cache at the ipconfig / flushdns command line.

After executing the command, it is desirable to reboot the system and make sure it works.

Questions about the preferences of proxy servers

Incidentally, it should also be noted that in some systems, the use of proxy servers for local addresses is enabled by default. This parameter affects the network and access to the computers in it.

In the settings of the IP-protocol, you need to switch to additional options and disable the use of the proxy, if this is not provided by the provider's connection settings. It is doubtful, of course, that the proxy is initially used, nevertheless it will not hurt to check the settings. In addition, you can experiment even with addresses. You can enter IP manually, but only in such a way that it differs from the gateway address by at least four or five dozen. That is, if the router has the last digit 0 or 1, the computer must include the address 40 or 50 at the end.

Finally, another reason why a connection does not work can be the use of a VPN. At least, at the stage of access to unlocked resources, this function should be turned off. And the speed of the Internet will be higher, and the response waiting mode from the site will be reduced, otherwise it will just get a 504 error like Gateway Timeout, which indicates that the default gateway is not available, or simply speaking, the router itself, which router or modem is.

Summary results

As you can already understand from all the above material, the WiFi ByFly connection itself does not represent anything particularly complex. In principle, all actions very much resemble the connection to the provider "Rostelecom" (at least, the main parameters used by the router and its settings look the same). The only difference is that the first operator very often uses the Bridge scheme, and the second one is based on the network operation in the PPPoE mode. Otherwise, if you understand these simple rules for setting up a connection, you can use them for any devices and operators (providers), if for some reason the automatic setting of parameters is impossible.