Homeliness, Tools and equipment
Cold welding "Poxipol": instructions for use
If you need to glue details or fill gaps and gaps, you can use "Poxypol", the instruction for which will be described in the article. This glue is a pasty two-component epoxy compound that has fast-setting characteristics. Known mixture as a cold welding.
Scope of use
If you need to glue rubber or metal, faience or wood, glass or concrete, then you can use the "Poxipol" welding, which must be prepared before use. It is quite widespread today, because it can be used in different areas, among which:
- Gluing brackets and hooks;
- Strengthening knife arms;
- Gluing of glass;
- The repair of toys;
- Gluing aircraft models;
- Repair of furniture;
- Strengthening of floor tiles;
- Carbide and carpet plastering;
- Sealing holes in aluminum sheets;
- Fastening of guides;
- Threading on metal and wood;
- Filling cracks.
Among other things, "Poxipol", the instruction for use of which should be studied before use, will allow you to glue the broken dishes, repair the boat, stain the leak or glue the mirror. This composition can be used to install instruments in laboratories and gluing aquariums.
This composition can strengthen the tile on the walls or repair the plumbing. Some masters apply a mixture for the repair of fishing rods and concrete floors. Effectively, "Poxypol" eliminates holes in concrete and metal containers, and also acts as a sealant for tanks and tanks.
Instructions for use
"Poxipol", the instruction for use of which should be known to you before use, is prepared in sufficient volume. Specialists do not recommend "milling", preparing a volume of at least 1 cm 3 . It is important to observe the proportions 1 to 1.
Work must be carried out at room temperature. After preparation of the composition for 10 minutes, a chemical reaction will occur. When bonding, you do not need to use a press and press the parts against each other excessively. Do not expose the detonation elements, the design should be left in a rest position.
The polymerization will be shortened in time if the temperature of the environment is slightly higher. If the temperature is lowered, the drying period will be somewhat longer. An hour after the application of the surface composition can be subjected to grinding, drilling and sawing.
"Поксипол", the instruction on which application should be known not only to experts, but also to house masters, completely will dry up in day after mixing of components. Ingredients should be mixed well before use. It should be remembered that transparent glue acts as a dielectric.
Recommendations for the use of glue
If you want to achieve a positive result when bonding, the surface must be cleaned of dust and dirt, grease and oil marks. Only then the glue will work. For materials such as rubber, metal, concrete, glass and ceramics, as well as rigid plastics, fibro-concrete "Poxypol" fits as well as possible. However, polyethylene, Teflon and polypropylene composition will not stick together.
"Poxypol" - cold welding, which should be applied to a rough surface. To do this, the smooth parts are sanded, and after the preparation, a lot is applied. You can do it even under water. If you want to work with complex surfaces, then to improve the adhesion, it is recommended to apply a thin layer of contact adhesive, which must be allowed to dry for half an hour. This applies to products made from:
- of stainless steel;
- Bronze;
- Ceramic tiles;
- Copper;
- Galvanized steel.
Such adhesive preparation should not contain toluene.
Temperature of use and other application features
"Поксипол" for metal perfectly approaches. The composition has the characteristics of rapid curing. The temperature of use can vary from 20 to 24 ° C. After a 10-minute break, the composition will change color to transparent and harden without changing its own volume. The work area will reach its maximum strength in 24 hours, which is true if the room temperature changes from 21 to 25 ° C.
The adhesive "Poxipol", the instruction for use of which should help you avoid mistakes, has insulating properties. However, this is true if the ingredients you mix to a homogeneous mass. As additional positive features it is necessary to allocate an excellent resistance to sagging. The tensile strength is 8 MPa. The adhesive has a different degree of resistance to chemicals. For example, the composition is excellent under the influence of water and the environment. Somewhat worse the mixture will cope with hydrochloric and sulfuric acids, mineral oil, as well as gasoline and toluene.
Security measures
"Poxipol", the temperature of use of which should not differ from the recommended one, is applied in accordance with security measures. It is important to avoid contact with the skin and eyes, as this can cause irritation. If this still happens, then it is necessary to wash the skin with a solution of soapy water. In the cured state, the material is not toxic.
Conclusion
Cold welding is used everywhere today. This is due to its excellent characteristics, including metal hardness and resistance to spreading even from vertical surfaces. The mixture can be applied by any tools, the thickness of the layer can be different, the material does not expand after drying and does not shrink. In its composition there are no solvents, and after solidification it can even be drilled.
Before drying, the adhesive can be leveled with a knife or spatula, after moistening the tool in water. If the mass can not be squeezed out, then the tube needs to be heated a little. Caps on tubes should not be changed.
Similar articles
Trending Now