Boiler "Baxi": Error E10, instructions for troubleshooting. The basic error codes of the Baxi boilers

Boiler equipment of the latest generation has smart automation, which turns off the device in the event of a malfunction, and also informs the consumer of possible malfunctions. To this end, the manufacturer supplies the heating equipment with displays, through which the user receives information about the main error codes.

It should be noted that one of the promising areas in the development of engineering communications is the use of gas for heating apartments and houses. Manufacturers offer their products in a wide range, which allows you to choose the right machine for any room. As an example, you can consider the boiler "Baxi", the error E10 in the display of which - a fairly frequent phenomenon. This equipment can be installed in any room, it is suitable not only for residential buildings, but also for manufacturing organizations. The premises where the device is installed must meet certain standards. For example, the boiler house in the volume should be 15 m ³ , and the height of the ceilings should not be less than 2.2 m. With the help of good ventilation it will be possible to guarantee the intensive air exchange, which is necessary for the operation of the heating equipment.

Troubleshooting guide

If you purchased a Baksi boiler, the E10 error may become a reality for you. Therefore, before starting the operation of such equipment, it is necessary to understand the main types of malfunctions. They are identified by codes, which can be divided into two groups, namely: the transition of the equipment into a standby mode or the complete blockage of the functioning of the device.

In the latter case, you can solve the problem by simply rebooting the unit. This error indicates that serious problems arose that could create dangerous situations for human life and health. That's why such a failure should be treated with special attention. Among them, there should be a lack of traction, lack of fuel supply, and overheating of the device. If you purchased a "Baksi" boiler, the E10 error can be eliminated on its own. However, without human intervention, such an outcome is unlikely. But if this happens, then it can be argued that the automation switched on the device on its own.

Description of error E10

The most common problem is the error code E10, which you can see on the display under some circumstances. The reason can be caused by the incorrect operation of the sensor, which monitors the circulation of the coolant in the system and the functioning of the pumping equipment.

Automation can work in those cases when the pressure of the coolant has been reduced to a critical level. This can also lead to a lack of contact between the pressure switch and the board. In some cases, for consumers who use the Baksi boiler, the E10 error is caused precisely for this reason. It may result in a malfunction of the pressure switch or an improper operation of the sensor of the pumping equipment. This code can also indicate the malfunction of the pump itself. Sometimes this problem is caused by clogging of the heat exchanger or the filter system that is in the heating circuit.

Error Solution E10

If the above error appears on the display of your boiler, it is not always correct to solve the problem yourself. If the pump fails, then as the only true solution to the problem will be its replacement, this task by the home master can not call specialists. If you have a gas boiler "Baxi" installed in your house, an error E10 may appear on the display when the above described character crashes. To solve the problem, you can also clean the filter system yourself. If you notice that the problems are related to other parts of the equipment, then the best way to set up the performance is to entrust the professionals.

Error E01

A fairly common error code is the designation E01 on the display. It can be inferred by the equipment when the sensor controlling the flame is triggered. The data may fail when:

• Absence of gas supply;
• Absence of contact with the sensor;
• The lack of correspondence between zero and phase in phase-dependent models;
• Contamination or malfunction of the sensor;
• If the gas valve fails;
• If the electronic board fails.

Sometimes an error E01 results in a failure in the ignition system or insufficient air access, which must be supplied for normal combustion. If an error E01 appears on the boiler display, this may indicate an insufficient fuel pressure in the system.

Recommendations for troubleshooting E01

If, during the operation of the equipment, the error E10 appears on the Baxi boiler, how to eliminate it, you could learn by reading the information above. However, this code is by far not the only one that can indicate a malfunction of the equipment. For example, if the device displayed an error code E01, then the user should check how correctly the sensor is connected. Experts recommend checking the fuel supply, sometimes it also happens that the gas supply is stopped, and the reason is only a closed gas valve.

If you are sure that all elements are OK, it is recommended to press the "R" button and hold it for 3 seconds. If the operation occurred accidentally, then the operation of the device should be normalized. Sometimes the operation is repeated, in this case it is recommended to contact the service center. Sometimes the E01 code is indicated by problems with electronics, and interference in it can be detrimental to the boiler.

Additional error codes

If you purchased the Baxi Mine For, the E10 error is not the only code that is one of the most common in the operation of such equipment. It should also be noted that the additional error codes that occur in the operation of such devices are: E03, 25, 26 and 35. Each of these errors will also indicate that the operation of the boiler has been blocked.

Error 03

This error code may appear after a rather long time when the user actively exploits the boiler. Some consumers note that the display shows these designations from time to time, and then disappear by themselves.

To remedy this situation, it is necessary to clean the blades well, because they can easily collect a lot of dust. Sometimes the grease of the bushing wears out, like the heatsink axes, which are located on the rear of the engine. This causes the fan to slow down. If even after cleaning, the situation can not be rectified, in this case it is necessary to consult a specialist. Do not worry before the time, if the display shows error E03, first you need to check all the hardware settings.

Error with code E35

A fairly common equipment for heating in recent years is the gas boiler "Baxi". Error E10 (how to eliminate it, was mentioned above) is not the only malfunction that sometimes accompanies the operation of such devices. If you encounter an error code of E35, the problem can be expressed in the flame monitor. This node is necessary to provide a signal about the presence of a flame before opening the valves.

The reasons for which the sensor did not work could be very diverse, but the most likely of them are the ingress of moisture and condensation to the electronic board, the problem can also be a parasitic flame. If it is an electronic board, then it is necessary to look for it in the boiler itself. But if these assumptions were not confirmed, then the reason should be sought in the undamped flame, which remains after the equipment is turned off. The manufacturer emphasizes that this problem may be due to insufficient valve tightness. But most often this error is eliminated with itself, for this you need only try to restart the boiler.

Errors E25 and 26

In some cases, the Baki boiler produces an E10 error, but if you see a code different from this on the display, you need to consider the causes of the problem more seriously. For example, an error of E25 may indicate an excess of the maximum temperature. The manufacturer speaks about it. In this case, it is necessary to pay attention to the temperature sensor of the heating circuit. But first you need to check the pump, as well as the cleanliness of the filters, the clogging of which in the heating system can lead to insufficient circulation of the coolant.

If there is an error E25, the pump equipment may simply be blocked. But there is also the possibility that the heating system is partially or completely inflated. The last action, when all of the above assumptions are excluded, is checking the temperature sensor. It can break down. If you also chose the boiler "Baxi", the error E10 (what to do to eliminate it, it was described above), of course, can arise. However, not only this code indicates some problems in the operation of the device. Sometimes there is also an error E26. True, it is much less common than all the others. This code is associated with a temperature sensor failure. If the device has issued this designation, then you can be sure that the temperature has risen above 20 ° C.

The rarest mistake

On the positive side, the Baksi boiler proved itself among consumers. Error E10 (how to fix, it was mentioned above), unfortunately, sometimes arises. It is one of the most common. In contrast, you can give an example of error code E00, which you may not encounter during the entire life of the equipment.

There is such a code with a breakdown of the stabilizer. The simplest way out of this situation is to replace this node. Some consumers, however, note that this alphanumeric designation indicates a failed board. The manufacturer himself denies this assertion.

Conclusion

Do not assume that the breakdown often accompanies the boiler "Baxi". Error E10 (how to fix, the instruction for carrying out these works - all this was presented above) appears very rarely, as well as other problems. However, for effective use of the equipment, you need to familiarize yourself with the information on the main faults, in which case you will know whether you can solve the problem yourself or have to call a specialist.