Asymmetric loop for feeder

Asymmetric loop is simply indispensable for those who prefer to fish in rivers and long distances. The use of such mounting positively affects the glue, since the feeder does not jerk at the same time. Accordingly, the fish behaves more calmly, is not frightened.

Advantages and disadvantages

Like any rigging, the asymmetric loop for the feeder has its pros and cons. It can be attributed to the merits of a very good sensibility (which has a positive effect on fishing efficiency), the transmission of a signal about a glitch at the very tip of the fishing rod, the lack of a sense of resistance to the weight of the fish.

The disadvantages of rigging are that an asymmetric loop can be confused when using long and thin leashes. The apparent "congestion" of the line makes it too noticeable in the reservoir. Fish can begin to behave too cautiously. In addition, in reservoirs with a cluttered or overgrown bottom, installation of feeder rigs is also not recommended .

Asymmetric loop is used, as a rule, in reservoirs with a clean bottom and slightly unclear water at medium depth. In this case, fishing will bring a very good catch.

Asymmetric loop or paternoster - what to choose?

Choosing a snap for the feeder, lovers of fishing can face the following problem. Which is better: an asymmetric loop or paternoster? On what to stop? In what cases is it necessary to use what equipment? Very simple, according to many fishermen, is Gardner's loop, the asymmetric, in turn, has a special sensitivity. In fact, you just need to decide in what conditions the fish will be caught.

Do not forget that the paternoster is knitted on the main line. The adapter to the swivel in the snap is missing. As a result, the main line is often twisted.

Asymmetric loop is a separate snap, knitting on a monofilament. With the main fishing line it is connected with the help of a swivel. Due to this, the tackle is much more sparse.

Principle of operation with a glue

When the fish is selected for bait and grabs it, there is no particular difference between such attachments as an asymmetric loop and paternoster. Using long leashes allows you to easily take prey. The fish, without fear, catches the bait and walks off to the side to eat its find away from everyone. But after the victim cuts into the feeder, distinct differences between snap-ins become apparent.

Using the paternoster

So, the difference is "obvious". When using a paternost, fish should not be detected. When striking the trough of the leash, a sharp hook pierces her mouth, and the fisherman needs only to pull his victim ashore. It is best to use the paternoster when catching bream, which moves quite sharply.

However, fish is also more suspicious and fearful, because it is repeatedly enough and again spits out the bait. When pulling, it starts to worry even more, that is, for such a clove longer leashes are needed. The fish in this case swallows the bait deeper, in order to enjoy it in peace.

Using an asymmetric loop

Absolutely in a different way is the situation at the bottom of the reservoir when the fisherman refuses the paternoster. Asymmetric loop for the feeder is thrown, after which, for a good stretch, the braid is wound up. The feeder starts to move along the line, as a result, stopping at the lowest point of the rigging. It remains only to wait, when the fish grabs the nozzle. After that, she drags her to the side to the very end in the upper edge of the loop. At this time, the feeder tip is visibly twitching. This indicates that it is time for the angler to cut, so that his prey does not spit out the bait.

Thus, when catching this equipment, the fish are not cut, but actually bite. The free running of the hook enables the fisherman to receive the necessary signal in time. The main thing is to use long leashes when fishing for an asymmetric loop. The fish should swallow the bait as deeply as possible.

Accordingly, the asymmetric loop remains more sensitive in comparison with the paternoster. A particularly good result it will show when catching a small fish in standing water.

What can be a loop?

Variants of this equipment are very diverse. Asymmetric loop, the photo of which can be seen in the article, first of all stands out for its length. It is this criterion that gives the so-called "free running" of the rigging. In a word, the longer the loop, the later the fish will rest in the feeder. Needless to say, active biting will require a reduction in the length of this rig, passive - on the contrary, increase. By the way, the choice of the size of the leashes is much more important than the choice between the asymmetric loop and the paternoster. This is known to every avid fisherman.

The length of the leash also depends on the location of the bait. Fish behaves in absolutely different ways in different places of its dwelling. In a reservoir with a strong current, the bait spot is rather elongated, so it will be a meter away from the feeder itself. In this case, the length of the leash is determined directly on the spot. Small fish, as a rule, feed away from the feeder, large - near. By the way, if the feed is slightly stirred, the glue often increases. Therefore, for greater freedom of bait, you must immediately lengthen the leash.

However, for any current and for different fish will have to select the right size. The necessary criteria for the leash are set by each fisherman independently, only on the basis of the main recommendations.

In any case, it should be noted that the asymmetric loop is not any worse than the paternoster, despite the fact that the latter is not inferior in effectiveness either. That is, the preferences of fishing enthusiasts depend solely on the variety of fish, the depth and flow of the reservoir, etc. The most important thing is to try experimenting. An excellent catch of the fisherman as a result will be provided.

How to knit?

Thus, if the fisherman wants to reduce the overlap and increase the elasticity of the leash, he needs an asymmetric loop. How to knit it, everyone decides for himself. There are several ways to achieve asymmetry.

The easiest way is to take a hard line with a 1.5 meter length of a small diameter (about 0.3 mm). The best way for mating is fluorocarbon. Although you can use another fishing line. The main thing that it was really tough. A suitable line will be straightened out immediately after it is wound on the finger several times and released.

Once the desired piece is selected, it must be doubled. One of its sides should be 10 centimeters shorter than the other. After this, using a double or triple knit, a small loop is sewn. On it will be attached a leash with a hook.

The next stage of mating is the most difficult. It is necessary to make a tight and rigid leash. It affects the propensity of the snap to entangle. When it is thrown, the feeder must go forward, and the leash - to deviate to the side. Due to this, it does not get tangled in the loop.

To make a leash, you need a double line about 15 cm long. It is made of double twist, after which a double knot is knit at its end.

A swivel is passed through the long side of the line, designed to secure the feeder. Next, the required length of the asymmetric loop (30-70 cm) is measured, and it is tightened with a double knot.

In order to attach an asymmetric loop to the main line, the swivel is put on the end of the loop and tightened by the knot. This ends the binding. The ends of the line should be cut as short as possible. Otherwise, entanglement snap can not be avoided.

Storage

The new asymmetric loops are best stored in small cellophane bags. Although in fishing stores you can buy and special boxes or covers for them. In addition, to date, the attention of fans of feeder fishing is represented by a variety of boxes in which you can store everything you need for a successful hunt.