"Ariston", washing machine: error codes, reasons for their occurrence and repair

The company "Ariston" produces washing machines, which differ in parameters, as well as constructive elements. Many inexpensive models often break down due to wear and tear. The most common problems are motor breakdowns, and also modules.

Also, the washing machines fail sensors. There are a variety of reasons for breakdowns of models. In this case it is important to understand the device of the washing machine and to know the basic fault codes.

Motor breakdowns

Error F01 indicates that the washing machine is faulty motor. The cause of this situation can be a burnt out condenser. Also, the motor breaks down due to network overloads. If this error is detected, you can try to diagnose the failure yourself.

Engine Repair

When the washing machine breaks down the firm "Ariston" , the error codes help you figure out what's wrong. You must first disconnect the device from the network. Further from the person it is required to remove the back cover. In many models, the motor is located at the bottom of the structure. The protective plate on it is fixed on the screws.

Washing machine "Ariston Margarita 2000" is produced with an additional protective harness. If there is a darkening on the wiring, it means that the motor has blown a capacitor. It's hard to replace it yourself. In this case, it is more expedient to completely change the motor. It is important to know the marking of the product and contact a specialized service center.

Causes of the breakdown of the tachodchik

In inexpensive washing machines, the puller often goes out. The code F02 is displayed on the display. If this failure is detected, you can find out the cause of the problem yourself. As a rule, it consists in overheating of the module. Also, the router often breaks due to network congestion.

Repair of the chipper

If the washing machine produced by Ariston is broken, you need to study the error codes in order to understand what went wrong. The tow truck, for example, can be removed by yourself. To do this, it is important to twist the lid, first to examine the module of the model. Also, experts recommend fully checking the fee. In order to make a full test, you will need a tester. It is important to check the resistance on all nodes of the module.

Tadhodchiki in devices are located near the drum. To remove them, use a conventional screwdriver. The next step is to look at the base of the tackler. When the contact breaks, the circuit closes. If the device is working properly, the tester will show resistance at 40 ohms. If the contacts are all right, then the control module should be checked. With a software error, the card is completely replaced.

Temperature sensor errors

Sensors very often break down in inexpensive washing machines. The reason for this is the overload of the central module. If the voltage rises sharply in the network, the capacitor may not survive. The main problem is that the sensors are expensive.

Repair of temperature sensors

When the washing machine breaks down the firm "Ariston", error codes can tell a lot about many things. You can try to examine it yourself, find out the cause of the breakdown. If the temperature sensor is faulty (code F03), it is recommended to remove the panel and check the module first. In this case, the part should also be tested. To this end, you need a quality tester to measure the resistance level. The temperature sensor in many models is located near the rotor. It is connected through a small contact.

To remove it, you have to use the key. Many modifications have a protective plate. It is fixed to the body, it can be easily twisted. After detaching the sensor, the element is checked by the tester. In this case, the resistance should not exceed 30 ohms. If the device shows a zero value, then the element must be completely replaced. Sometimes, together with the sensor, you have to completely change the control module, but this happens rarely.

The causes of level sensor faults

Code F04 Indicates that the model has a faulty level sensor. Thus, the machine leaks, or water is not recruited. Level sensors most often fail due to a wiring fault. In this case, the contacts can be oxidized. After seeing code F04, you need to check the level sensor and clean it.

Level sensor repair

To remove the level sensor, it is necessary to twist the cover and disconnect the protective plate. The above element is always near the drum. It is attached to screws or locks. Many models have a small shelf under the element. After detaching the part, the protective cap is checked. Contacts must be clean and free of defects.

If the user notices dark spots - the level sensor must be cleaned with a cloth. The cap must be twisted counter-clockwise. Inside the sensor, everything must be clean. If any items are found, they are extracted. At the end of the work, the element is replaced and checked. If there is a problem with the water in the tank, replace the part.

Drain pump errors

The pump for the washing machine is a very important element. If the specified part fails, the drum does not fill with water. The drain pump is quite expensive. The main causes of the failure of the part are the faulty valve and filter. The problem can also be dirty water, which clogs the pump.

Repair of the pump

If the washing machine does not turn on the Ariston firm, the error codes may appear different. When the pump is faulty, error F05 often appears. You can try to replace this part yourself. For this purpose it is recommended to prepare a key and a set of screwdrivers in advance. The first step is to remove the protective cover from the washing machine. Then you need to disconnect the rotor, get the pump directly. The pump for the washing machine is fixed to the rack and fastened with several clamps.

Before twisting the pump, check the thrust. Pipes should be pushed aside so that they do not interfere. The pump is lifted from the counter strictly upwards. At this stage, it is important not to damage the valve. If the pump is damaged, the part must be completely replaced. Some experts advise installing new pumps on two pipes. They have a larger parameter of limiting pressure, and they are produced with several linings. Many models are equipped with a sealant. If there are cracks visible on it, then the device will have to be changed. After installing the pump, it is important to check the strength of the nozzles and securely tighten the screws.

Causes of button error

For all programs of the washing machine the Ariston Dialogic module answers. This element is on the motherboard and plays an important role. When it fails, the display shows code F06. If you find this problem, you need to disconnect the washing machine from the network. The main causes of the module malfunction are thyristor overheating and diode wear.

Repair module

Repair the module in a washing machine is very problematic. First of all, it is important to detach the element, check the resistance on it. If the problem is with diodes, then they can be replaced. In this case, the card is removed and the thyristor is extracted. The resistance is checked at the input contacts of the element. In the normal state, the model emits 55 ohms.

When the thyristor breaks, the resistance is greatly overestimated. The presented element is quite expensive. Modules of old models are problematic to get in the service centers. Also it is worth noting that many elements differ in parameters.

Errors of heating elements

The heater for washing machines plays an important role. He is responsible for heating the water. When the element exits, the user sees the code F07 on the display. If a problem is detected, disconnect the model from the network and learn more about the malfunction. As a rule, the heater is broken due to dirty water. Also, problems with the network can cause a malfunction. However, with the failure of TEN can be understood independently.

TEN repair

To change the heater's TAN, it is necessary to completely remove the drum. To do this, the user will need a set of keys. The upper seal can be pulled by hand. In this case, the harness is often fixed on the racks. To disconnect it, you need to strike the edge of the tape with something sharp. Then you just have to unscrew the heater. Some modifications are made with several elements. In this case, you need to check each heater separately. If the bottom of the heater is visible, then the device can no longer be used. You can change the part in any service center. When installing a new heater, it must be tightened very tightly to the stop.

The causes of errors in the TEN relay

Relay TEN in washing machines is broken very rarely. This element is responsible for heating the water directly in the tank by applying a voltage. The relay often overheats due to network congestion.

Relay repair in a washing machine

To repair the TEN relay, remove the protective harness and disconnect the tank. The element is immediately unscrewed and checked for defects. If the relay tube is visible, the plaque must be cleaned. The presence of black spots indicates the burning of the device. In this case, the heater will have to be completely changed. Elements are produced in different sizes, when buying a device, this should be taken into account. If we consider the early models, then the heaters are attached to them by level sensors. To replace the element, small cross-shaped keys are used. Before disconnecting the tank, a tourniquet is removed.

Some modifications are made with several rubber seals. It is also worth noting that new heating elements are fixed at the base of the frame and are allocated to large dimensions. To replace the devices, screwdrivers are used. Protective plates are usually installed on four screws. In many models, the relay is all-welded, and it can be disconnected from the tube. In this case, the part changes entirely.

If the tube can be seen plaque, then it is rather problematic to remove it. In this case, it is more appropriate to completely replace the element. Sometimes the "Hotpoint Ariston" (washing machine) breaks due to problems with the clamps. As a result, the relay is not able to hold securely. In this case, you can contact the professionals to install additional fasteners. Much depends on the frame that is in the washing machine.