"Starline A9": programming key fob. Car alarm "Starline A9": user's manual

Signaling "Starline A9" is very popular among drivers of different cars. The complete set of the system includes detailed instructions. It allows you to connect and configure alarms. The manual also describes the principles of operation of the system. Having studied user feedback and instructions, it is possible to single out the basic principles of working with "Starlight A9". Programming the keychain will be a simple task. The advice of experienced motorists will allow you to make adjustments quickly. This will enable you to use all the options. The alarm can be configured to run in autorun mode or without it. The lock function is also set.

General information

"Starline A9", the operating manual of which requires studying before starting the installation of the system and programming the key fob, is a signaling with remote start of the engine. It has a two-way radio link. Its range in the area without obstacles is 600 m. In pager mode, this indicator is increased by 2 times.

The coding of the radio signal is dynamic. Selection of control commands is carried out according to the cursor principle. Each command is controlled by its button. It is displayed on the keyfob display. The system provides for sound and vibration alerts.

In addition to basic data on the state of the car, the keychain shows the user the time, the temperature in the cabin, and an alarm clock.

It is possible to install the presented system on cars with diesel, gasoline or turbocharged engine type. The transmission can be automatic or manual.

Safety regulations

Using the functions of remote or automatic start of the engine, control of the nodes of the machine, it is necessary to follow the security measures of using the "Starline A9" system. The operating instructions clearly indicate them.

The car is important to park in a well-viewed area. In this case, it must be set to the parking brake. The automatic transmission lever must be in the PARK position and the manual transmission in the neutral position.

You can not start the engine in the absence of the driver in the cabin, if someone is in front of or behind the car. The key ring is inadmissible to give to children or persons who can not control this device. The machine must be in good order, its system must have a sufficient number of all consumables and fuel.

Key fob control

Stored alarm functions are performed automatically or by means of the keyfob signals. Some of them can be changed. The procedure is prescribed in the instructions to the "Starline A9" system. Programming the keyfob is easy. For this, the device has three buttons. The information is displayed on the LCD.

The car can be controlled by one or more key fobs. If you lose the main device with a screen, you can use the spare remote control. This keychain with buttons, which does not have the function of providing information to the user. With it, you can control almost all the functions of the system.

If the owners of the car use several key fobs with a display, all information about the status of the car's systems and alarms will be displayed on the screen of the device from which the command was given.

Button Assignment

The "Starlight A9" keychain with a liquid crystal display is configured with three buttons on the case. Their combinations make it possible to control the functions of the system.

Button I can turn on the programming command if you press it one time. Holding it for 3 seconds, the driver remotely starts or stops the engine. The user can activate the armed mode. For this, with the engine running, this button is also held for 3 seconds.

Button II with a short press sets the cursor position on the screen. If you hold it for 3 seconds, the trunk opens.

Button III also allows you to control the cursor position with a short press. It interrupts the alert signals of the key fob. To do this, keep it pressed for 0.5 seconds. To enable or disable the clock, alarm, power saving mode, this button is held for 3 seconds. If you hold it for 6 seconds, you can enter the programming mode of button I.

Pictures on the display

All information about the car's status and the alarm itself can be viewed on the display of the "Starline A9" system. The icons on the remote control help you navigate through the setup and control modes. The instructions clearly state which picture corresponds to a particular function.

Indication of commands and modes is displayed at the bottom of the screen. You can list it from left to right for a general idea of the functions of the device. To fully understand the purpose of each of them, you need to carefully study the instruction.

The first picture, which is on the left, corresponds to the anti-plague mode. If it is on the display, this command is on. Next is the function of the additional channel 3. Moving to the right side, you can see the autostart mode of the motor in terms of temperature. Next comes the function of daily autorun or engine start on the alarm clock. This picture is followed by a remote start or stop of the motor.

After that, the silent protection modes follow. In this case , the confirmation beeps will not work. The following picture corresponds to the guard function with an audible signal. It is followed by a shutdown at a shock sensor distance.

A little more to the right is the picture of Valet's service mode. It is followed by a picture showing the status of the car's systems and saloon temperature indicators. Then there is an additional channel 2. The remote opening of the trunk completes the picture chain.

Button I

Button I on the main keyfob is user programmable. This can be done an unlimited number of times. Most often it is used to turn off or turn on the guard mode in the "Starlight A9" system. Programming a new key fob is easy.

Press III to move the cursor around the screen. When the desired mode is selected, for example, the arming function or any other, the movement is stopped. Button III is held for 6 seconds. First, there will be two beeps. Then 3 more. Then I button is pressed to activate the selected function.

After this programming, pressing the button I briefly will turn on the previously selected mode. To set a new function for it, perform the above operation again.

Button II

You can also assign a function to button II. It is necessary to press button III several times. The cursor will move clockwise. If you stop for 1-2 seconds and continue moving, it will move counter-clockwise.

The pictures listed above will be selected one after another. When the cursor reaches the desired program, the movement with the button III stops. To execute the selected program, the user presses the button II.

10 seconds after pressing any button, the cursor returns to the original CHECK state. This command controls the condition of the machine and the temperature in its interior. It does not change the alarm status. Knowing this, the user will not have a question, how to look at the temperature on the Starlay A9 key fob. When operating this particular team is the most in demand.

Setting the clock

Starting to work with the system, you need to learn how to adjust the time on the keyfob "Starlight A9". It is necessary to hold the button III until two beeps are heard. The clock on the display will flash.

To increase the digital value of the hours, minutes, you need to press the I button, and to decrease the button II. The transition from hours to minutes is carried out by short pressing of button III.

When the settings are completed, you must exit the clock setting mode. To do this, hold down the button III until a single beep sounds. According to the manufacturer's instructions, you can set the alarm or timer.

Recording codes

The driver can independently enter into the memory of the system the codes "Starline A9". The keyfob programming is carried out in the disarmed mode. You can bind up to 4 consoles. It is necessary to do this if the alarm system for some reason does not see the signal of the key fob or the machine was bought with the already installed system.

To enter the programming mode, you must turn on the ignition. The service button Valet is held until four audible signals appear.

First set up the main keychain. On it, the buttons I and II are clamped. For additional consoles without a display, the buttons III and IV are clamped. After the successful recording of the first keyfob, one siren signal will sound.

For all key fobs the same procedure is performed. The interval between recordings should not exceed 5 seconds. Otherwise, the programming mode will end automatically. Then you need to turn off the ignition. The success of the operation will be confirmed by 5 flashes of the vehicle's side lights.

Engine starting

Many drivers are interested in how to start a car with a keychain. "Starline A9" when connecting the alarm involves programming the type of gearbox. If it is manual, the wire loop is cut during installation (as indicated in the instructions). If the car is an automatic box, this element is retained.

The type of the motor is also specified. There are two possibilities of remote starting the motor. In the first case, you need to place the cursor on the corresponding icon on the display screen. Then press button II. Or, simply press the I button for 3 seconds.

At the first attempt of start-up, 3 beeps of the siren will sound, 3 flashes of parking lights. The key ring will emit a melodic signal. The icon on the display will remain lit. You can set the warm-up time of the motor.

Reset settings

Sometimes the driver may need information on how to reset the Starlay A9 keyfob settings. Actions are performed in a certain sequence. First turn on the ignition. Then the service button Valet is pressed 10 times. After this, the user turns off the ignition. Entering the reset mode is made if after these manipulations, 10 beeps of the siren sound.

The service button needs to be pressed one more time. After that, another siren signal will sound. The driver presses the I button on the master key fob. A short beep will sound. This means that the reset was made. From the setup mode, the system will exit automatically after 5 seconds. The parking lights flash 5 times. The key ring will emit a melodic signal.

Having considered the peculiarities of the car alarm "Starline A9", you can easily program the keyfob. Before working with the equipment, please read the manufacturer's instructions. This will allow you to use the built-in functions fully. If necessary, you can return the system to the factory settings. Control of the key fob will allow to use the car's security system comfortably and fully.