Knitting with knitting needles

Work on the product almost always ends with the cutout of the neck. The most common cut, which never goes out of fashion, is a round neckline or neckline. It can be large or small. Make such a cutout as follows. From one third of the hinges of the front part, the gate is tied, and the remaining two thirds are the shoulder sections.

Knitting with the knitting needles of the neck, you need to start a few centimeters below, exactly as much as the centimeters of the width of the bake. The loops, located in the center of the neck, are transferred to the thread. After that, each half of the top is peeled separately, subtracting through the row two times in three, once in two and three times in one loop. Just before the shoulder cut, knit exactly until the end. After the shelf and back of the model are connected, sew the right shoulder of the product and on the needles, the hinges are cut from the edge of the left shoulder to the hinges of the neck, the hinges removed from the thread are looped, then the hinges are cut along the other side of the cutout and the hinge from the backrest cutout, Which are also filmed. Baku knit, as a rule, an elastic band two to three centimeters high. When the last few rows are used, they switch to smaller needles to make the bake better lying. Then all the loops are closed, making an elastic edge (the hinges are closed according to the drawing). Beku can be associated with any other pattern.

Knitting with knitting needles with a sharp neckline is beginning to make out at the height of the armhole. Divide the hinges of the front part into two, leaving one loop for the middle (it is removed by a string). Gradually, on each side, first one loop is removed eight times in each fourth row, and after six times in each sixth and twice in each eighth row.

Knitting with knitting needles with a sharp neckline with covered baits produces simultaneously with the bake as follows. Two centimeters below the armhole, the hinges for the left shoulder, half of the cutout loops and another loop are assembled on the spoke, and the remaining loops of the front part are assembled onto the thread. The first few loops left on the spoke are tied with an elastic band (this will be the width of the bake). Loosen the loops between the elastic band and the base viscous, as in the usual sharp cut. On the right shelf, knitting with the knitting needles starts from the fact that seven spokes are added to the knitting needles on the back side, then the loops are transferred from the thread to the knitting needle and the neck is tied in the same way as the left one. After registration of the right shoulder, the crochet continues to be knit another 15 cm higher, for the backrest detail. Then it is sewn on the neckline of the backboard separately.

Quite often knitting products start from the neck and knit an integral part including the back, in front and two sleeves. A feature of this method of knitting is a strict calculation of loops, without which the work may not work. First determine the circumference of the neck and make the necessary calculation of the loops. Knitting sweaters from the neck begin from the outer edge of the collar. For example, if a collar with fastening tabs is provided, then the number of loops required for the collar is increased, and loops are added to the width of the fasteners. By tying the desired height of the collar, the loops begin to decrease so that the collar lies better in the neck area. The adjustments are made at the same distance from each other. After finishing the tying of the collar, they switch to knitting the product itself. Strictly in the pattern define the lines of raglan, on which the addition of loops will be made. Additions are made from both sides of the lines of raglan. Knitting from the neck of the main product begins with the calculation of loops from the neck along the lines of raglan. The number of loops for the backrest should be twice as much as for the sleeves. For each shelf, it is necessary that the number of loops be equal to the number of sleeves loops plus strap hinges. The success in work with this method of knitting, as already noted, depends on the correct calculation of loops, as well as on a good pattern, which is constantly needed to verify the progress of work.