Automobiles, Cars
Installation of a parktronic on the "Kalina": with their own hands
Numerous SRTs advertise their services to install parktronics, but it is expensive. Installing the parking sensors on the "Kalina" can also be done on its own - the process is not complicated, and if you have certain skills, you can perform the installation very carefully.
How is the system of safe parking
A special electronic unit receives information coming from the sensors, and then notifies the driver of the obstacle. Sensors are the main devices in this system. It is thanks to these small devices that work on ultrasonic technology, parktronic knows how to detect obstacles.
Completeness
So, the device is already selected and purchased - depending on the cost and the manufacturer, it can be differently manned. So, manufacturers from China often pack parking radar in simple plastic bags, and more serious brands from Europe and the US supply their products in beautiful boxes with a set of fasteners. There is also an installation manual.
Dyeing sensors
The installation of party sensors on the "Kalina" with their own hands begins with the preparation of sensors - often on cars of the brand "Lada Kalina" bumpers are painted in the color of the body. The sensors of the parking radar, regardless of price and manufacturer, are not painted or made in a different color. To avoid damaging the exterior of the machine after installation, the sensors must be pre-painted.
Marking work
Installing parktronics on the "Kalina" with their own hands is a simple task that even a newcomer can do. However, in this operation there is one difficulty - it consists in marking the rear or front bumper under the holes for the sensors. Here you need to calculate all the parameters correctly.
We install the parking radar on the "Lada Kalina" in the body of the station wagon
Installation of a parktronic on the "Kalina" station wagon can be performed as follows. You can install the sensors along one line in the middle of the retroreflectors. In this case, the extreme elements are set 3-4 cm from the edges, and the rest are mounted through 40-45 cm.
Remove or do not remove the bumper
There are also two options. Installation of the parking sensors on the "Kalina" can be carried out without removing the bumper - at the same time the wires of the senders will be pulled by wire. Many consider this technology too expensive in terms of effort and prefer to dismantle the bumper.
How to make holes for sensors
Manufacturers equip parktronics with crowns, which with a drill or a screwdriver can drill neat holes.
Professionals recommend those for whom the installation of parktronic with their own hands ("Kalina" or any other car) is the first serious tuning, do not work at high revs. Haste will not lead to anything good. The holes must be drilled as slowly as possible - then you can achieve perfect results.
High revolutions during drilling will provoke the heating of the crown - plastic bumper can melt. This will greatly complicate the process of pulling the crown. The edges of the hole also decrease. In this case, you will have to modify them using the file. By car "Kalina" installation of parking sensors will be done neatly, if you drill slowly and allow the crown to cool before the next drilling.
Installation of sensors
Further, when the holes are ready, you can start mounting the sensors. On the reverse side, each sensor has a UP mark and an additional arrow. For these marks, you should orient the sensor in the hole. Then it is fixed by means of latches. Manufacturers complete the sensors with different types. In the event that the clips are silicone, you will have to additionally bring them with a screwdriver. So do the equipment in China.
When the sensors are installed, it is necessary to purchase platforms for the installation of screeds - they can be found in any construction supermarket. The surface must be thoroughly cleaned and degreased - the areas on the double-sided scotch are attached between the sensors. Next, the wires are assembled in one bundle, and at the end they are put on the corrugation and put into the trunk through the hole under the left lamp from behind. After that, the bumper can be installed on its rightful place.
Connectivity
Next, the two wires are connected to the reversing lamp. To do this, you need to wrap the trunk in the trunk. You can use crampons to connect the wires. To the rear light connect plus and minus. The control unit is connected according to the instructions and fits anywhere in the trunk. So the installation of parktronics is performed (the "Kalina" station wagon is no exception). It remains only to assemble the cabin, turn on the ignition, put the gearshift lever on the rear gear and check if the installed device is working. Also you need to connect and attach the display or indicator. Then you can use parktronics on the car "Lada Kalina". Installation parktronika, as you can see - a really simple operation. With it, even novice motorists can easily cope with it.
Similar articles
Trending Now