How to use a screwdriver: step by step instructions

Everyone at least once in his life did repairs at home or performed work related to the repair of his apartment or dacha. Today an irreplaceable assistant in the repair is a screwdriver. Buying it, be sure to find out the power, configuration, as well as the warranty period for this power tool.

Safety precautions

Before using a screwdriver, be sure to read the safety information in the instruction booklet attached to the tool. Often this tool is used in production. As a rule, the instruction "How to use a screwdriver" must be mandatory in the acts on labor protection. To avoid accidents, working with a screwdriver, you must comply with all safety regulations. Do not trust the tool to people who do not know how to use a screwdriver, and can not comply with safety regulations. For example, children, the elderly, sick people and people in a state of intoxication.

Use this tool, pre-donning overalls and glasses. Remember that any tool, whatever it is, is a source of danger.

How to use a screwdriver battery

Before starting work, make sure that the battery of your screwdriver is fully charged. Insert it into the charger and pay attention to the indicator. The green color of the indicator indicates that the battery is charged. The red color of the indicator indicates that it needs to be charged.

In order to increase the working time of the screwdriver, it is enough to have a second battery. After the first is discharged and you replace it with a second one, the first one is inserted into the charger. After the battery is charged, do not hold it in the charger. This shortens the battery life as a whole. Also detrimental to the battery life is too hot or too cold room temperature, in which the screwdriver works. The mode of operation of a single battery is designed for five hours.

How to fix a bit or a drill bit

You can fix a drill or bit in a screwdriver in two ways. The first way is manual. The bit is inserted into the socket and tightened by hand. The second way is to tighten the bit or drill with a rotating cartridge, hold it with the second hand. Check how you secured the bat, it's very simple. Try to twist one screw, and you'll understand whether the bit is scrolling or not.

How to use a screwdriver correctly

On the screwdriver there is a scale with which you can adjust the direct power of rotation. Turning the knob, you choose the mode that you need depending on the work that you intend to do. With the same controller, you can select the drilling mode. Just do not try to drill hard screws, concrete and stone surfaces, so as not to disable it. For drilling hard surfaces, there are specially designed tools for this. Do not switch the regulator while the screwdriver is operating. This may cause the tool to malfunction. Knowing how to use a screwdriver, you can extend its service life.

With the help of a special switch, you can select three operating modes. Twist mode, twist mode and lock mode for the screwdriver. The third mode is needed for security. All these modes are very convenient to switch if you hold the screwdriver by the handle located above the battery. The handle is usually covered with rubberized material and is therefore very safe to work with. It ensures that the screwdriver does not slip out of your hand at the most inopportune moment. For greater confidence, you can fasten a screwdriver to your hand with a special strap.

Drilling mode

If you decide to use a screwdriver as a drill to drill a hole in wood or plastic, then in order for the hole to be of good quality, you need to lay a flat piece of wood under the objects that you drill. So you can avoid cracks and chips during drilling.

Drilling holes in metal implies compliance with certain rules. The location of the future hole must be nocked. This will help avoid sliding the drill over the metal surface. Selecting the drilling mode on the screwdriver, do not forget that when drilling a metal, the drills at the outlet of the metal are often broken. To avoid this, try not to press strongly on the screwdriver while drilling. If the drill is stuck, then the screwdriver can be unscrewed into the twisting mode. If you are drilling a small piece, then in order to hold it, use a vice.

Application screwdriver

Those models of screwdrivers, which are sold today in stores, allow you to pick up the bit to the screw so that fitting them to each other is tight. And to adjust the screwdriver so that tightening each samorez was ideal, it became very simple.

Do not think that a screwdriver can be used, only to drill, twist and twist the screws. While repairing the car, it is possible to twist and tighten the nuts and bolts, grind various surface attachments. Building furniture without using a screwdriver takes a very long time. Hanging cornices for curtains or bookshelves with a screwdriver is much easier than running with a screwdriver and applying effort. So today, the screw driver took his place of honor among the most necessary tools in the household.

Care of the tool

The timely cleaning of the screwdriver with a soft rag will prolong its service life. Do not allow water and moisture to enter the screwdriver. Store in a dry place. Do not drop the screwdriver. Trying to handle the screwdriver neatly, also follow the charger and its power cable. If you notice both a malfunction in the operation of the screwdriver itself, and a malfunction in the operation of the charger, then try to contact the service center. Turning to specialists, you will get high-quality repairs and high-quality spare parts, which will considerably prolong the service life of your screwdriver.