How to turn on the water heater:

Unfortunately, the residents of most modern multi-storey buildings are familiar with the problem of periodic shutdown of hot water. Therefore, many citizens who do not want to put up with even short-term inconveniences get boilers. But for comfortable operation it's not enough just to install the device, you also need to know how to properly turn on the water heater.

First start of the device

It should be understood that the installation of the boiler should be handled by a qualified specialist. Otherwise, the device will lose the right to warranty service and repair. It is also advisable to instruct the master to start the technique. However, if this moment is already lost, then this can be done by yourself.

Before turning on the water heater, It is necessary to check the installation quality and make sure there are no leaks. To do this, it is necessary to collect water in the device that is disconnected from the network. To understand when the tank is completely filled with water, you must always open the hot tap. Flowing water from it will be a signal about the filling of the boiler. After this, it is necessary to screw the tap and carefully inspect the equipment. After verifying that there are no leaks at the connection points, you can connect the equipment to the mains and set the desired temperature for heating the water.

How to use a working boiler?

It's one thing to figure out how to turn on a storage water heater. But Many are interested in how it should work, so that it can save energy. To date, there are two diametrically opposed views on the operation of the device. So, some people argue that it is more economical to turn off the boiler for the time when they are not being used. Actually this is not true. The instrument is much easier to maintain the preset water temperature constantly than to heat it again.

In addition, experts claim that the constantly filled tank is less susceptible to corrosion. The second nuance, which should be taken into account during the installation, is the device grounding. It is necessary to check that the installers do not miss this important moment, because the safety of the whole family depends on it. Before turning on the water heater, You need to check if there is water in it. Running an empty device will instantly fail.

Selecting the water heating mode

Before How to turn on the water heater, It is necessary to determine in what mode it will work. Some owners are trying to save by setting a low water heating temperature. In reality, this only reduces the efficiency of the device and does not provide any savings. However, some modern models of boilers provide an economical mode of operation. In this case, the water will be heated to 55 degrees. The saving is that at this temperature, a minimum level of scale appearance is achieved, which saves owners from having to frequently clean the tank.

Features of operation of a flow-through boiler

Such devices are convenient in that they do not provide for the limitation of the volume of hot water. The only nuance is that it is not designed for simultaneous showering and washing dishes. In addition, with a strong head of water, its temperature will not be too high. Before installing such a water heater, you need to make sure that the electrical wiring of the apartment is powerful enough to withstand such a load. Incorrect installation can leave without electricity, not only your apartment, but the whole house, so the installation of the device should be handled by a specialist.

How can I turn on the flow water heater correctly? Check the pressure level of the tap water. If it is good, then you can turn on the system, if not, then start it better to postpone. The temperature of water heating is regulated by means of buttons located on the body of the device. After the water procedures are completed, you must turn the tap on and turn off the machine. In most modern models, it is planned to save the settings that were set for the first time, so when you turn it on again, water immediately from the appliance will be fed to the set temperature. In the process of operation, scaling is formed in the system, which must be periodically removed by washing the filters under a strong head of running water.

How do I turn on the water heater after the protection has tripped?

Like any other modern technology, the boiler is equipped with a built-in protective device. It is located inside the thermostat and operates in case of excessive overloading of the device. In most cases, the automatic shutdown of the boiler indicates serious malfunctions. With a single protection operation, you can simply press the button on the thermostat and turn on the device. In the case of a triple protection operation for a short time, it is necessary to find out the cause of the trip and address it.