How to tie a line to a reel: ways and tips

For proper and fruitful fishing, all gear must be properly prepared. Every modern angler in the arsenal has a reel that greatly facilitates his life with forced transitions during fishing and is an integral part of the rigging.

Naturally, during the winter period this device is almost not used and, therefore, is put on hold until the season of catching on open water. During storage, the line grows old and loses its properties. Experienced anglers update each season before each season. Then the question arises, how to tie the line to the coil. This will be discussed in this article, but first we describe the device and the types of coils.

Types of coils

In principle, there are two types of coils: inertial and inertial. The first is used mainly for primitive float rigging and fly fishing rods. The second type of coils is the most common and is used universally. He got his popularity due to the design, which allows you to make long casts and quickly select the line to yourself in the bobbin.

The device of inertia-free coils

The main components of the coil are:

• The housing in which the gears, bearings, wings, shafts and other related parts are installed.
• The rotor, which is a movable part, is directly attached to it by the mechanism of the forest depositor.
• The spool is a fixed element in which the fishing line is stored.
• Friction, allowing to extinguish powerful jerks of fish, thereby saving the line from the cliff.
• A handle that transmits the rotational movement of the hand to the coil mechanisms.

Methods of winding the line on the spool

There are three main ways to wind the fishing line on the spool:

• straight;
• With the use of winding;
• With the use of lining.

Each of them has its own advantages and disadvantages, so they are usually used in individual cases.

Direct winding of the line to the coil

If the rod is the simplest, and the coil is one of the cheapest, then in this case the capacity of the bobbin does not exceed 50-60 meters. Since the length of the line is on average 100 meters, it fills the bobbin in full.

The correct filling of the bobbin is considered when from the edge of the edge to the boundary of the wound line remains 1-1.5 millimeters. This allows you to do the longest casting. The line under a slight tightness is wound on a bobbin. How to tie a fishing line to a reel in this way?

At the end of the line is a loop with a double or single knot. Further in this loop a large free loop of the main line is inserted, which is put on the bobbin. It turns out a kind of self-tightening yoke.

The disadvantage of this method is that with a spool volume larger than that of the existing line, a rim at the end of the spool is inevitably formed. He will prevent further casting. And if you harvest the line in the same volume as the bobbin, then this will make such a method quite expensive. Because the meter line is good money, and it will not be used practically.

The winding of the line on the reel with the use of a lining

Correct the drawback of the first method will help the backing layer on the base of the spool. For this, a layer of tape or tape is wound. This measure reduces the volume of the spool.

The disadvantage of this method is that the fishing line, wound up under pressure, deforms the insulating tape, and over time the glue penetrates into the main layer of the line and thereby glues the turns and prevents unwinding.

The winding of the line on the reel with the use of winding

How to tie a fishing line to the reel to reduce the rim without flaws? The solution to this difficult task came to us from America. In the original it sounds like backing, and our angler-athletes called it a winding.

The essence of this method is to get the missing layer of fishing line cheaper. Since the lowest layer of the forest is practically not used, it can also be replaced relatively cheaply.

How to wind a fishing line to the reel by backing? This happens in several stages. First the main working line or a woven thread is wound. Further, it is associated with a fishing line intended for selection. The volume of the line is selected taking into account the millimeter thickness to the edge of the spool.

The second stage is rewinding the resulting volume to the working spool. This allows you to leave the ballast layer of the line at the base, where it is practically not used.

Frequent questions of beginner spinners

When winding the line on the bobbin, beginners have a lot of problems. The very first of these is how to tie a line to a reel without assistance. Since the line must be laid flat and layer by layer, it is necessary to do this under a slight tension. To do this, a piece of cloth, in which you can pinch the line during the winding, is suitable.

After winding, the following question arises: "How to fix the line to the coil, in order to prevent its involuntary unwinding?" To solve this task, a carbine and a paper band will work. The carabiner is attached to the free end and is fixed to the leg of the coil with the help of a rubber band.

How to knit a fishing line to a reel with a lock and can it be done?

Some types of spools have a red flag - a clamp. It can not be fixed if it is planned to fix the line for the accuracy of the casting length. This is one of the grossest mistakes of beginners.