Homemade gas-stove from a gas cylinder: drawings

At the onset of cold weather, many owners of garages ask the question of heating. This is especially true of those rooms in which people are from time to time. To equip them with a stationary system is impractical, in some cases this approach is completely impossible to implement. However, you can not do without heating. You can equip a system that operates on electricity or solid fuel. Among the second variants, a stove-burger can be separated from a gas cylinder. Even such a master who does not have enough experience will be able to do such work.

Recommendations for work

If you are going to be made a gas turbine from a gas cylinder, it will become a practical solution for premises that occasionally need heating. Such a stove quickly heats up, while a comfortable temperature can be achieved in a short time. It is worth considering that the oven cools down as quickly, in which its main drawback is expressed. This problem can be solved by the method of creating a brick shirt. However, the master must leave a small gap between the metal and the masonry. Only this way the equipment will quickly warm up and cool down further.

When making the construction on the body, it is necessary to make holes in the amount of 2 pieces. Their shape should be rectangular. One is useful for loading fuel, while the second will act as an ash-bluff. As the main structural element is the hull, among other things, there is a chimney in the system.

Quite often in the process of manufacturing, the ash-box is combined with a compartment where ash is collected. It is recommended to equip one more door here, which will make it easier to clean the structure. The principle of operation of the equipment is quite simple. In the furnace should be laid fuel, the combustion of which will be allocated heat, heating the metal body. The latter, in turn, will give heat to the air, quickly warming up the room. When a gas turbine is manufactured from a gas cylinder, it is supplied with a chimney, which will remove harmful combustion products from the room.

Nuances of works

The master must take into account that the chimney, which has a short length, will produce heat along with the smoke outside. This approach can not be called rational. That is why the pipe must have a broken shape. It will improve the efficiency of the furnace. As a fuel for the operation of the system, you can use almost everything that can burn. It can be coal, firewood, old clothes, carpentry waste, household garbage and so on. Another plus of burzhujki is that its design is universal and simple. Thus, the equipment can be used not only for heating, but also for cooking.

Technology of work

If you are going to be made a burzhuyka from a gas cylinder, then you need to start the manipulation with the preparatory work. This procedure is mandatory, otherwise the gas that remains in the tank may cause an explosion after interacting with the spark generated during cutting. To begin with, unscrew the cylinder valve, allowing the gas to escape. At the next stage, the capacity is turned over, which helps to get rid of the condensate. It should be noted that it has an unpleasant smell. Therefore it is recommended to collect it in a container. If the drops fall on the floor or other surface, the weathering will take place long enough.

A gas bottle can only be made after careful preparation of the hull. The container should be installed vertically, and then it is filled up to the top with water. This will help the remainder of the gas, which could stay inside, go outside. Then the container is turned on its side, and the water is drained. Now the balloon can be subjected to further manipulation. After the preparation has been completed, the master must decide which type will be baked. It can be vertical or horizontal.

Manufacturing of a horizontal structure

The gas turbine from the gas cylinder, the drawings of which are presented in the article, can be located horizontally with respect to the plane. For the beginning, the upper part of the cylinder is cut off. Then the grate should be installed inside the vessel . It is most often formed from reinforcement. The bars should be carefully bent by a snake. Installation of the bars is quite easy. They are mounted in a container and fixed with a welding machine.

Manipulation of the front part

Now comes the turn of the front. To do this, you should take a steel sheet, which outlines the contour of the circle. The diameter of the latter should be equal to the outer contour of the container. Next, the wizard can start cutting the part. Inside the circle, two rectangular openings should be marked. The first is necessary for supplying fuel to the chamber, while the second one is intended for an ash-pit.

Assembling

When a gas turbine is manufactured from a gas cylinder, the drawings help to carry out the work without making mistakes. The next step is to start cutting holes in the previously prepared circle. To do this, use a Bulgarian or chisel. To the finished cover you need to weld the veils and fix the doors on them. The latter are pasted along the contour with an asbestos cord. This design is attached to the balloon by welding. On this we can assume that the front of the furnace is ready.

Now you can proceed to the back. There is arranged a chimney pipe. To do this, a hole is made, the diameter of which is equivalent to the diameter of the pipe used to remove the smoke. A chimney of the necessary shape and dimensions is attached to it. For a chimney, use a thick-walled pipe. After that, the furnace can be used, since it is completely ready for operation.

Vertical construction

Homemade gas turbo from the gas cylinder can be vertically oriented. In the manufacture of such a design, the system may have two embodiments. The first provides for more manipulations that are associated with the cutting. But with the installation you will face much less difficulties. When choosing this method with the help of the bulgaria, you should get rid of the top part of the container. The second method will save you time and energy. But it is considered extremely inconvenient. When a pyrolysis vessel is manufactured from a gas cylinder according to the second method, the upper part remains in place. At the front, a big hole is to be cut out. Below there is an aperture for ash and ash cleaning.

Conclusion

You can place holes freely. The main condition is that in the lower part there are two rectangular holes. Now the grates are being prepared. They are welded between rectangular holes. When the stove-burzhujka from a gas cylinder are carried out on the first method to establish a lattice simply enough. Whereas in the second method, the grate should be installed through the upper opening.