From the gas cylinder brazier. Mangals - photos, blueprints

Hardly audible crackling of firewood, a quiet evening and the smell of fresh vegetables and meat, grilled on the grill of the barbecue ... This is one of the best ways to restore strength and get a charge of positive mood. And if everything was done independently, including from a gas cylinder brazier, then in addition to a good rest will have confidence in their own abilities.

The principle of assembling a brazier

The main purpose of any mobile design for frying products is to ensure the maximum comfort of the cooking process. For this, you can buy factory models of the barbecue, but not always their quality corresponds to the cost. Therefore, attempts are often made to make mangala independently. But before starting the assembly it is necessary to find out the basic principles of its construction.

It is often possible to find a homemade brazier from a gas cylinder. A photo of such constructions speaks of the relative simplicity of their manufacture. But without a competent approach, the operating life of the brazier will be minimal. Therefore, you need to find out the principles of its assembly:

• The material of manufacture must meet the safety requirements.
• The selected balloon has no obvious and hidden defects.
• Additional accessories (mesh, stand) are also made of non-combustible material of metal or steel.

Taking as a basis these rules, you can eventually collect from the gas cylinder brazier, the quality of which will be no worse than the factory models.

Material selection

For the practical implementation of the idea of creating a barbecue with their own hands, you must first choose the material of manufacture. The basis of the design will be a household gas cylinder. It is recommended to choose non-standard sizes with an increased diameter and a relatively small height. As an example, you can take a product with dimensions:

• The height is 610 mm.
• The diameter is 292 mm.
• The volume is 27 liters.

The thickness of the walls should be at least 3 mm. To save money take a used cylinder, so you need to carefully check the body for integrity and the absence of obvious signs of deep corrosion.

For the manufacture of support elements (racks), it is best to use a metal pipe of circular cross-section. In addition to cooking shish kebab, you can make a grid for a barbecue. To do this, take any suitable workpiece and trim it according to the internal dimensions of the cylinder.

Drawing

It is best to plan a universal brazier from a gas cylinder. Drawings of this design should include overall dimensions, accessories - racks, hinges, mesh and handles for carrying. Before drawing up the work plan, the surface of the cylinder is cleaned of dirt, its geometric dimensions are measured.

Then, based on the available materials, an assembly drawing is drawn up . It indicates all the changes in the design of the cylinder. Since the standard length of the skewer varies from 30 to 45 cm, the lid must be made removable. To do this, mount the hinges in one direction - in this case, the upper part of the construction can be quickly removed. The length of the racks is also indicated in the drawing. It should be such that the final height of the structure is convenient for cooking.

Materials and Tools

Make a gas cylinder mangal can only by having the necessary equipment and supplies. They are selected according to the drawing prepared earlier and the technological scheme of manufacturing. The minimum list of tools is the following:

• Welding machine. You can use a low-power model, since the amount of work will be small.
• Power tools - drill and angle grinder.
• Roulette, building level.

With practical skills in working with a welding machine, in the absence of a welding machine, you can use the rental service. If you plan the whole event in advance, then the production takes a maximum of one day.

Of the materials you will need a gas cylinder, a steel pipe (meter according to the calculation in the drawing), a grille. After selecting the above components and tools barbecue barbecue from the gas cylinder is ready for practical implementation.

Preparatory work

Before starting the assembly, it is necessary to process the cylinder for its modification. Since in the process of operation it may contain the remains of gas, in the first stage it is necessary to get rid of them. To do this, remove the valve and leave the container in the open air for 1.5-2 hours. After this, you can proceed to surface treatment.

Using a grinding weight, the paint layer is removed and the integrity of the housing is checked. Final processing is recommended only after construction. Performing work is best outside the room.

Assembly

After the completion of the preparatory phase, you can proceed directly to the construction of the structure. First, the valve is removed using a grinder (grinder). Then the balloon is installed horizontally and the line of the cut is marked out.

When performing work, safety precautions should be followed. Therefore, special protective goggles and gloves must be worn. To prevent changes in the geometry of the surface during cutting, the treatment line is moistened with water. After removing the cover, you should carefully examine the internal condition of the cylinder. Minor defects (rust) are processed until complete removal. In this case, the thickness of the product should not be greatly reduced.

The next stage of the work, after which it will be made from the gas cylinder brazier, is to make grooves on the end surface to fix the skewers. Their number is determined by the height of the workpiece. For normal preparation of shish kebab the recommended distance is 20-25 cm.

Further, according to the internal dimensions of the product, a metal grid for barbecue is made. The length of the resulting hole is measured and the blank is reduced from the data obtained. For mechanical strength, it is recommended to install the stiffeners on the mesh along the perimeter. Loops are welded to the body. They must be steel so that they do not lose their shape when the brazier is warmed up. The final stage of manufacturing is the installation of racks. For greater stability, they should be located at the edges of the structure.

This is the most popular technology for making mangal. Photos, drawings and their operation speak of reliability and relative ease of assembly. But for an excellent result, you must first take quality material and components. Only in this way is it possible to produce a functional reliable brazier.