Knives for knives. Use and self-manufacturing

What is knife knife? This is the name of a special kind of braided lace, which is tied to the hilt of the weapon with one end. Using it, you can make the knife more functional and aesthetic. For what this adaptation is specifically needed and how to make it yourself, we will consider further.

Main functions

There are only two main types of straps:

1. With a loop. Such an adaptation is necessary first of all in order to prevent the loss of weapons in the event that it accidentally slips out of the hands. At the felling of such a sword with a hinged loop let a little, but relieves the load from the brush. You can also quickly release your hand. The knife will just hang on it. If necessary, the arms can be suspended for a loop during transportation or storage. Loop knives for knives are the most functional.
2. Lacing or "tail". When using this variety, the knife can be removed very quickly from a pocket or cover. Lace in this case is a kind of flexible continuation of the weapon itself. With wide movements, the knife to which such an attachment is attached behaves more predictably, as it acquires additional inertia. Another function of these tambourines is purely decorative. Sometimes they serve as an ornament, for example, a premium weapon.

Kinds of devices

To distinguish the knives for knives can by the way weaving the lace. A loop can also be executed using different schemes. In addition, there are different nodes, with which the attachment to the hilt is performed. Very often, the lace is additionally hung with decorative accessories. These can be shards, beads, etc.

From what you can weave

The knives for knives can be woven from almost anything. But the most acceptable option can be considered a synthetic lace. Such material will last a long time, as it is wear-resistant and does not decay. Experts advise using a round, not flat lace. It is desirable that its color be bright enough. If the knife falls, say, into grass or snow, in this case it will be easier to find. Sometimes even ordinary new shoe laces are used.

In addition, it is necessary to choose the right length and width of the lace. From these parameters, ultimately, the size of the finished product will depend. To make a thick and short hood, a coarse volumetric lace about half a meter long will do.

Weaving the tambour with our own hands

With your own hands, you can make a very practical kneading knife.

Weaving begins with the preparation of a pre-purchased cord. Its ends should be slightly melted. In this case, the fastening to the knife will be more reliable. Weaving is carried out in several stages:

1. A hole about 5 mm in diameter is drilled in the knife handle. If, of course, it is not there initially. Sometimes there is a special loop on the knives. In this case, you do not need to drill anything either.
2. The cord must be cut into two pieces of 25 cm. One of them is tied to the handle by an ordinary knot. This cord will need to be attached also to the middle of the second part. A very good solution would be to take two different color cords for work. In this case, much more attractive knives for knives are obtained.
3. The resulting four free ends of the cords will need to be weaved into a cage. This technology is very simple. The ends are superimposed on each other at an angle of 90 degrees. In this case, each previous cord passes under the one that is located in front. In the process of weaving, the ends should be tightened as tightly as possible. In this case, the finished product will be more convenient and will last longer. In addition, tightly woven tambourines look much more neat.
4. After finishing the weaving, it will be necessary to tie the knot. The ends should be trimmed, trimmed, and hidden inside the resulting product. Sometimes they are pre-melted. This can prevent the cord from loosening. However, it should be taken into account that the lamb itself will be less reliable. A finished product can simply be uncoiled at one time, and the laces become entangled. In this case the knife from the knife will have to be cut off.

If desired, you can learn how to make very beautiful and practical knives for knives with your own hands. The technology discussed above is absolutely simple. A convenient device for a knife can be made in a couple of hours.