"Interskol P-26 / 800ER" (puncher): specifications, user manual, repair, reviews

Before choosing a puncher, you need to decide which tasks will be assigned to the equipment. It is important to consider whether the list of options is all you need. Some models offered for sale have very limited functions, which positively affects the cost. Some units have only one drilling mode, others - two: drilling and impact. If you want, you can buy a punch with three modes, to the previous two you will add a chisel.

Features of choice

By weight, the punchers can be divided into light, heavy and with an average weight. The weight of the first does not exceed 4 kg, while the average may have a mass within 5 kg. As for the heaviest instruments, their weight is sometimes 10 kg or more.

It is important to pay attention not only to the basic set of functions, but also to the manufacturer, which should have a good reputation among consumers. Among others in a wide range in the market of construction equipment are perforating guns "Interskol". The P-26 / 800EP is one of the models of this supplier, it will be discussed below.

Model Description

This perforator has an acceptable cost - 4600 rubles. The model is capable of operating in one of three modes. Working attachments can be replaced almost instantly, this will help the cartridge SDS-plus. The perforator "Interskol P-26 / 800EP", which you can read about below, is safe for operation. The operator will be securely protected by a safety clutch in the process of using the device if the equipment is blocked in the material.

In addition, the manufacturer supplied the equipment with a reverse function, it is represented by turning the carbon brushes. This contributes to a longer period of their operation and uniform power with versatile rotation. The set is complemented by a depth limiter, through which it is possible to drill holes with certain parameters.

Specifications

The puncher "Interskol P-26 / 800EP" weighs 2.9 kg. The power of the equipment is 780 watts. You should consider that the device does not have a drilling chuck and vibration protection. Drill holes with concrete in this concrete with a drill, their diameter is 26 mm. If you use a crown, then with its help in the brick it will be possible to make holes with a maximum diameter of 68 mm. In the metal holes with this model of the perforator can be done with a diameter of up to 13 mm.

Additional features

This version of the equipment has a speed control. The frequency of impacts varies from 0 to 5400 per minute. The puncher "Interskol P-26 / 800EP" has three operating modes. The maximum impact force is 3 J. The length of the cable is equivalent to 4 m. In wood, the maximum drilling diameter is 30 mm. The design is equipped with a safety clutch. Some consumers and specialists are interested in the spindle speed parameter. It can vary from 0 to 1250 per minute.

Feedback on the main advantages

Consumers like the perforator "Interskol P-26 / 800EP" described in the article with the SDS-cartridge. This is due to a variety of reasons, among the main ones:

• functionality;
• high performance;
• Modern design;
• Turning the chisel;
• Presence of a safety clutch;
• Reverse;
• Additional handle;
• Depth gauge;
• Case.

A simple change of tooling the consumer can carry out with the help of the cartridge SDS-plus. To protect the user and tool when the drill is jammed, the design is equipped with a safety clutch. For a reliable retention of the tool, you can use an additional handle, which the home masters consider very comfortable. In order to make blind holes, you can use the depth gauge.

Repair of puncher

Repair of the perforator "Interskol" can be carried out independently only after the expiration of the warranty period. The task of eliminating mechanical damages is more complicated than when the electronics fail. Immediately to establish the cause of the breakdown can be quite difficult. First, you should visually inspect all the details, and after the breakdown is identified - to fix the problem.

If you are confronted with the fact that the device turns on, but does not bang, a broken switch could lead to a breakdown. The defective fingers of the switch may indicate a malfunction. They are constantly in contact with the rotating parts, this causes wear. However, it sometimes happens that the fixing device fails, which keeps it in the gear housing. In this case, the mode starts to switch spontaneously.

If this problem does not bother you, then you do not need to change the latch, because the punch will work. However, if you decide to repair the perforator "Interskol", you will need to replace the switch. If the right one was not found, and the work can not be stopped in any way, then the worn out part can simply be turned over to 180 ° C.

This approach will allow the work to continue. As for the cartridge, this part of the mechanism is subjected to the greatest loads, this sometimes becomes the cause of breakdowns. If you are faced with such a problem, then the cartridge must be simply replaced. Extend the life of it by preventive maintenance: cleaning from dirt and washing with gasoline from dust.

Methods of work

The puncher "Interskol P-26 / 800EP 2" has a hammer and a compressor ring. The failure of these elements can occur due to the impressive loads. If you are faced with a breakdown of this kind, then the only way out is to replace the node. When the reducer breaks down, it is first disassembled and checked for all the details. The most vulnerable place is the bearing. It must be checked for integrity. It should be replaced, if such a need arises. But the reason can also be covered in the seat. When it is produced, it starts to hold the bearing poorly. The body of the perforator in this case will have to be replaced.

Quite often the gears of the reducer also become unusable. Having inspected them visually, you can understand, whether so it. Repair this part of the puncher in no way, you will need to replace it. The puncher "Interskol P-26 / 800EP 2" may encounter an oil leak. This happens very rarely. But if it does happen, then you only have to replace the stuffing box, which is located in the neck of the body. It is possible to work with a perforator with interruptions and dirt. This is indicated by gnashing and crackling. In order to avoid such a problem, from time to time it is necessary to clean and lubricate the internal cavity of the perforator. It is important to use the same type of lubricant, without changing it throughout the life of the device.

User's manual

The puncher "Interskol P-26 / 800EP" should be checked by the trial plug-in method in the shop. The start of operation should be accompanied by a safety check of the workplace. It must be kept clean, it is important to ensure its good illumination. If the workplace has been poorly lit or cluttered, this can cause accidents.

The electric machine must never be used in an explosive atmosphere, under conditions that may include the presence of flammable dust, gases and liquids. This requirement is due to the fact that the operation of the device is accompanied by the generation of sparks, which can cause ignition of fumes or dust. Plug plugs should be ideally suited to sockets. They should not be changed on their own.

Manufacturer's recommendations

For machines with grounding wire, it is not recommended to use adapters. It is important to exclude the effect of rain on the electric machine. It is not recommended to keep it in wet conditions. If moisture gets inside the enclosure, then this can cause a person to be electrocuted. The described puncher for concrete has a power cord, which must be handled with care. Do not use it to drag the tool and remove the plug from the outlet. The following shall not be affected by an electrical device:

• Sharp edges;
• butter;
• heat;
• Moving parts.

The risk of electric shock is increased if the cord is twisted or damaged.

Safety measures when operating a perforator

Using a shock machine, you should use hearing protection. It is important to remember that doing work may lead to damage to the buried electrical wiring. This is why the tool must be held by insulated handles during operation.

If there is a contact with the wiring, it may cause fire or electric shock to the operator. The perforator for concrete should be used only after using a metal detector you will find hidden engineering networks like electric, steam, gas and water pipes. The additional handle must be used during operation. It is included. The puncher should be held with both hands, taking a stable position.

It is important to remember that the tool can jam if its working parts fall into large fragments, stones or into reinforcement. On sudden jamming, the equipment will react with a backstab, this may cause loss of control of the device. If the tool jams, it must be immediately switched off. Release the puncher from your hands is possible only after the engine is completely stopped.

Features of the service

The characteristics of the perforator "Interskol P-26 / 800EP 2" were presented above, but this information is not the only one that you should familiarize with if you decided to purchase such a model. The operator needs to know how the unit is serviced. Before starting such manipulations, it is necessary to remove the plug from the socket. For safe and high-quality work after the end of operation, it is necessary to clean the machine and the ventilation opening of dirt and dust. After use, clean the binding axle.

If you notice that there is no rotation when turning on the equipment, a malfunction of the impactor or gearbox may indicate a similar problem. Sometimes it happens that the motor does not work when the device is turned on. It is important to check whether there is voltage in the network. A faulty plug or switch may cause this problem. Sometimes the power cord or wiring is cut off. If you hear increased noise in the impactor or gearbox, its parts may be worn or broken.

Cost of consumables and spare parts

If you needed a drill bit for concrete for a perforator, then you can buy it at a cost of 40 rubles. and higher. Prices vary depending on the size of the drill, parameters, manufacturing quality, manufacturer. When choosing it is important to pay attention to the parameters. For example, a drill bit for concrete for the perforator of the following sizes, 6x160 mm, will cost the consumer from 48 rubles. If the dimensions are 10x1000 mm, then you can buy a drill from 400 rub.

Whatever the quality of the equipment, it may require the replacement of spare parts. For example, a button switch you can buy for 1260 rubles., While coal brushes will cost the consumer 450 rubles. Manufacturers advise to use original spare parts for the perforator "Interskol P-26 / 800EP". Thus, the rolling clutch will cost the buyer 2,100 rubles. As for the case of the reducer, it can be bought for 1820 rubles. The piston shell costs 1,250 rubles, while the stator of the electric motor is 990 rubles. If you need to replace the anchor, you can buy it for 1390 rubles.

Conclusion

On how to implement the choice of a puncher, was discussed above. However, it should be remembered that it is important to pay attention to some other features as well. For example, the impact energy. If you have a light model in front of you, the impact force of the perforator will be approximately 2 J, while the tools of a more serious class are able to strike with force up to 15 J.

Choosing a puncher with more impact energy, you can ensure the possibility of making holes larger diameter. For some consumers this feature is paramount. If this value is small, then the device will not work as efficiently.