How to remove the rear wheel on a scooter: step by step instruction

A broken tire, repair of shock absorbers, brakes or muffler makes many drivers wonder about how to remove the rear wheel on the scooter. To make it more difficult than it seems at first glance. Although the second wheel is attached to just one nut, this operation may require special skills and knowledge.

Reasons for removing the rear wheel

Scooter, like any other vehicle, is subject to the laws of physics. Parts wear out and need repair. No exception are the wheels of the vehicle. At first glance, removing the rear wheel from a moped is easy. Yes, and it keeps on just one nut. But this is a deceptive impression. In order to get close to the rim of the rear wheel, the owner will have to sweat fairly, taking off most of the plastic and parts.

The reasons for removing the rear wheel from the scooter can be very diverse. Most often this flat tire, because few of the motorists at least once did not hit the wheel with a sharp object. But in the rear of the scooter, in addition, there are many important details, for access to which you will need to disassemble half of the vehicle. And what else could be the cause of the repair with the dismantling of the rear wheel? We list:

1. Defective brake pads. Brakes are the most important part in a motorcycle. If they do not work properly, you need to fix the problem as soon as possible.
2. Replacing the old wheel with a new one.
3. Wheel balancing.
4. Replacement of the reducer shaft.
5. Painting the disc.
6. Setting the drum brake.
7. Replacing a worn or punctured wheel.

Tools for work

Before you remove the rear wheel on the scooter (150 cm³), you need to find tools, without which in repair can not do. You will need:

• Allen key;
• A clean rag;
• Wooden bar.

A little luck and patience will help you to finish the job quickly.

The instruction on removal of a back wheel

How to remove the rear wheel from the scooter? The quickest step to understanding this is the step-by-step instruction proposed below:

1. Set the scooter so that the rear wheel scrolls in the air.
2. Remove the muffler. To do this, remove the seat and the plastic, and then unscrew the nuts on which the muffler is held. It is important not to take them out completely, but only to weaken them.
3. Using the wrench, unscrew the nuts securing the silencer to the cylinder. Remove it from the scooter. At the same time, a paranitic gasket may be lost, so be careful.
4. If the muffler is dirty, it can be cleaned of carbon and dirt. To do this, heat the outside with a blowtorch, and walk inside with a hard metal brush. After all the manipulations, the exhaust opening of the muffler should be covered with a clean cloth, so that foreign particles do not fall into it.
5. Most mopeds have a mono-shock absorber. If there are two models in your model, and they are located at the rear, you need to unscrew the nuts and dismantle them.
6. In the presence of a rear disc brake, you need to do the same: carefully unscrew the brake caliper and pull it aside.
7. And now you can proceed directly to the removal of the wheel. Unscrew the carrier nut using the shock wrench. If this is not at hand, the usual screwdriver will do. But in this case it is recommended to fix the wheel with a wooden bar.
8. Remove the wheel from the slot.

To install the wheel, reverse the above steps.

Scooter repair Honda

Japanese scooter Honda has long been in the top three best-selling vehicles with engine capacity up to 150 cm³. Modern design, thoughtful and comfortable seat, manoeuvrable chassis, engine with economical fuel consumption make Honda the favorite of many.

To undoubted advantages of the scooter can be attributed and the system of liquid cooling, and V-shaped transmission, and a 4-stroke engine with one cylinder. Consumed mopeds "Honda" about 2.5 liters per 100 km, and the speed can be developed up to 100 km / h.

When driving off-road, moped owners often run into sharp objects that can damage the tires. But to remove the rear wheel on the scooter "Honda" is not easy because of the burning on to the slots, which glues the parts together and complicates the process of dismantling. In this case seasoned scooters advise to spray with WD-40, and then gently tapped the wheel closer to the center through a piece of wood.

Troubleshooting the Racer scooter

The company Racer entered the world market quite recently. Nevertheless, its products have already attracted motorists. A distinctive feature of this scooter is the kick starter, which allows you to start it even when the battery is inserted. Fuel consumption per 100 km varies from 2 to 5 liters. The 4-stroke engine has an electronic injection system and can reach speeds of up to 80 km / h.

When repairing the wheels make it difficult to remove the two drum brakes installed at the rear and front. Therefore, the question of how to remove the rear wheel on the scooter "Racer" is very relevant. To do this, you need to do the actions described in the chapter "Instruction", but with one amendment. Before removing the wheel itself, it is necessary to loosen the brake cable, which "sits" on the pads. After this, the procedure must pass without special difficulties.

How to remove the rear wheel on the scooter "Irbis"

Another brand of scooters with an engine capacity of up to 150 cm³ is Irbis. The products of this brand are characterized by a brutal design, two powerful headlights in front and bright colors. Seeing such a scooter on the road, you will not confuse it with anything. The largest cubic meters of the model can reach speeds of up to 90 km / h. Disc brakes quickly stop it in case of extreme braking. Oil cooling does not allow the motor to overheat.

The reinforced suspension with two shock absorbers can deliver a lot of problems when removing the rear wheel. To access the bus, you must first unscrew the muffler mounts, and then the rear brake. The "Irbis" scooters are fitted with a mono-shock absorber, therefore in this part of the problems should not arise.

Recommendations from mechanics

You can meet a lot of recommendations and discussions on how to remove the rear wheel on the scooter. Experienced motorists recommend to use the penetrating lubricant WD-40 (or in extreme cases gasoline) to facilitate repair, and thoroughly clean the dirt and degrease before installation. Also it is strongly advised to lubricate the splines with grease. After installing the nut, it is recommended to tighten it tightly, with jerks, but without bumping. To hold the wheel in place instead of the bar, you can use a variator cap, which will not allow it to rotate.

In extreme cases, if you can not dismantle the wheel yourself, experts recommend contacting the nearest checked service. The same is worth doing if after removing the parts you found on one of them serious damage.

Results

Each scooter needs repair from time to time. Faulty operation of the vehicle not only hinders comfortable driving, but also jeopardizes the life of its driver. Repair the scooter with your own hands is easy, if you sit down beforehand and how to properly understand the details. Sometimes on some element the process can be stalled, then it is recommended to carefully follow the whole sequence of steps from the very beginning - perhaps somewhere there was an error. When replacing the rear wheel you do not have to hurry and be careful, and then you will succeed.

Success in repair and good luck on the roads!