How to make a loop on a line in different ways

Every lover of fishing should be able to tie the most common fishing knots, because without them you can not do fishing. This article will tell you how to make a loop on the line with various, most applicable and effective methods.

The main advantages of the nodes for the loop on the line are the simplicity of execution and reliability. It's rather difficult to run a really good knot for a beginner, because this work requires a lot of patience and practice.

Tips for knitting loops

• For maximum strength, the nodes must be pre-wetted.
• It is necessary to tighten slowly so that the line is not heated.
• On a monolayer, it is better not to glue the knots, after that they become brittle; Also it is necessary to consider, that for gluing on a braid the special viscous glue is required.
• If the site is tied poorly, then it is better to remake it. Good mating has no gaps.
• To insure yourself against surprises, it is better to tie knots at home, in advance. The quality of the node can depend not only on the skill of the fisherman, but also on the line (from the manufacturer, on its quality).

How to make a loop on a fishing line for a leash

Correctly tie a loop on the line for the leash in the following sequence:

1. On the main line is a loop that sticks to the finger where there will be a branch for the leash.

2. After that, you need to take a fishing line at the other end of the loop and make a few turns along the fishing line (7-9 turns). As a result, a rather large loop will turn out.

3. Then this loop is doubled. On the side where the line was duplicated, it must be divided again.

4. Further in the middle of a single line a loop is made, and already through it a double line is passed through. With the other hand you need to grab a new loop.

5. After this, the line is wetted and tightened. Here it is important not to tighten the knot too much - when applied, it will be tightened as it should.

How to tie a loop at the end of the line

To quickly and firmly make a loop at the end of the line, you need to learn how to knit a special surgical loop, which has proved itself in fishing. Such a loop looks like a "running" node and it is not too tight.

How to make a surgical loop on the line:

1. An open loop is formed at the end of the line. For her, a normal knot is tied. Then the loop extends along the same trajectory again.

2. After that, it is tightened to the desired size (before it needs to be moistened with water).

3. It only remains to cut off the excess ends of the line.

How to make a loop on the main line

This loop is needed to attach a leash to it. It is tied as follows:

1. To measure and notice the desired length, you can use the triple knot, which will act as a stop. After that, the leashes are fitted to the line.

2. To the node-limiter, you need to add one more, a double node, which is not fully tightened. Thus, from the double node the figure eight is obtained.

3. The end of the leash is passed to the received eight: first into one ringlet, then to the other. After that, the loop is tightened.

On the fluorocarbon fiber line

In this section, we will look at how to make a loop on the fluorocarbon fiber line. For it is better to use a special type of nodes, made according to the following scheme:

1. The end of the line is doubled. In length it should be about 10 cm.

2. This end extends into the ear of the swivel.

3. After that, it is added to the main line. The total length obtained should not be more than 5 cm.

4. As a result, the assembly is wetted and tightened.

The tying of a loop on the line of eight

Node eight is often used in fishing business, as it is simple enough to perform and the line he ties very firmly.

How to make a loop with a figure eight on the line? To do this, follow the following instructions:

1. The line needs to be folded twice and to make a medium-sized working loop.

2. In it, pass the hook for knitting and catch a small loop.

3. Sew it into the big one and remove the hook.

4. After this, hook another loop (corresponding to points 2 and 3).

5. Wet the scooped fishing line tightly, and the eighth loop is ready.

Sliding loop on the line

Sliding is made specifically to easily adjust the ring. How to make a loop on the line:

1. Throw a fishing line on the index finger.

2. Hook for knitting to hook the line from right to left, then turn the hook.

3. Now it remains only to stretch the noose.

Thus, we have considered the basic ways how to make a loop on the line.

Today there are a huge number of loops and knots, which are used by experienced fishermen. For a beginner to learn at least basic, you need to practice a lot. Knitting loops is a painstaking and time-consuming process. Without training here is indispensable. But do not forget that more experienced fishermen can always come to the aid of a beginner in knitting loops.