How to make a foam generator for washing with your own hands

Until now, contactless washing can be considered a luxury, which, especially during a crisis, many motorists can not afford.

The need for a foam generator

You can, of course, buy a mini-sink, but its price sometimes reaches 15,000 rubles. As an output there is a foam generator for washing. It's quite easy to assemble such equipment with your own hands. The cost in this case will be much lower compared to the finished product. The only element that will cost a lot is the compressor, which is responsible for injecting the air mass. It is recommended to buy it in the secondary market, and choose a low-power model.

Design features

If the foam generator is to be used for washing with your own hands, first you need to familiarize yourself with the features of such equipment. The device is able to perform two tasks at once, namely the formation of foam, as well as its uniform distribution over the body surface. The jet passes through the solution in the tank, mixing with the air. In the end, foam forms. This process can not be called complete. Inside such a foam generator, the substance must obtain a certain density. Why soap water is injected onto the foaming tablet. It should be resistant to corrosion, so you do not have to worry about the integrity of the element. Plate-regulators should be placed in parallel, this will give a flow of liquid, which will have a flat shape. The presence of a long hose, which is equipped with a device, will allow enough comfort for the car enthusiast to wash the car. As a detergent in the equipment used to use car shampoo.

Features of manufacturing a simple foam generator

If you decide to make a foam generator for washing with your own hands, you must first purchase a compressor. It will be convenient enough to make manipulations with the use of a sprayer. The design of this device is almost identical to the factory-built tank. The walls of the sprayer should have a thickness that can undergo pressure within 5 atmospheres.

Technology of work

From the sprayer you need to get the fitting and the valve. This will get 2 through holes. At the next stage, the hand pump is disassembled and muffled . The next step will be the preparation of some elements for the creation of equipment, among them one can distinguish a check valve, a pipe connection tubing, a hose adapter, four nuts, and a 2-pound drill with a diameter of 0.5 inches. An air fitting, foam pill and gaskets are useful. Drivings need to be screwed into a plastic tank, and then fixed with all nuts. It is important to use gaskets that will ensure tightness. Selecting one of the drills, you need to screw the check valve with the union. Then, as on the other, a tank is installed to connect with the inside pill. On this we can assume that the foam generator for washing by one's own hands was carried out. To the fire, through which air will flow, it is necessary to fix the tube. The air should go from below. This will allow the liquid to foam.

Recommendations for specialists

When a foam generator is made for washing by hand from a sprayer, at the final stage some manipulations with the hose are to be made, however they will not take much time. To its ends it is necessary to strengthen the garden sprayer. After the structure is ready, water is poured inside, as well as a special cleaning agent. Use at the same time you need a ratio of 10 to 1. Before the process of operation, it is important to tighten the throat tightly. After the air supply is switched on, the spray can be activated. The car enthusiast should know about the average consumption of a special shampoo, which will be 20-50 grams per wash. If you decide to perform a foam generator for washing with your own hands, the scheme of which will help you carry out these works, it is important to take into account the fact that the work is not particularly difficult. It is important to ensure the pressure of the compressor, which can reach 4 or 5 atmospheres. Manipulate the assembly of the master will be an opportunity for a short time, as a rule, it takes about 2 hours.

Making a foam generator from a plastic can

Foam generator for washing with your own hands (photo presented in the article) can be made from a plastic can. This technology is even simpler than the above. Assembly can be made from improvised materials, spending a minimum amount of time and effort. The master must prepare the Bulgarian, a plastic canister, a compressor, a set of wrenches, a gun, a nozzle and flushing hoses.

Manufacturing process

It is worth noting that the foam generator for washing with own hands from a vacuum cleaner can also be manufactured. Do not have to buy a compressor. However, if you decide to use a technique that involves the use of a plastic canister, you will need to prepare an inch tube, the length of which is 70 cm. It is filled with a line of different cross-section that will eventually give you a homemade mesh. Both ends should be closed with plugs, in which there must be threaded holes. One of the plugs of such a device is equipped with an adapter, which has the shape of the letter T. The second one fixes the union. The hoses are fixed to both outputs of the adapter. At the same time, it is important not to forget about the presence of shut-off valves. One of the hoses of this design will be connected to the tank with liquid. Then the other - to the compressor. This method allows you to get a foam generator at home, costing the least. The first activation of the device should be accompanied by pouring into the reservoir of ordinary water with some amount of dye. This approach allows you to identify the weak points of the equipment, if they have a place to be.

Work on an alternative reservoir

If you decide to assemble the foam generator yourself, then it is important to give the reservoir a choice. The simplest techniques were presented above. The best reservoir tank can be considered a propane gas cylinder. He is able to undergo all sorts of pressure. With its help, you can provide a fairly impressive flow, without fear of damage to the device. Foam generator for washing with own hands from a fire extinguisher can also be made. Thus it is necessary to use welding. Initially, all the old holes are brewed, and then two new ones are made. One of them must be located at the bottom point of the end, while the second one will be in the central part. To them, welded tubes equipped with fittings.

You can use both couplings and adapters. The main element of the device must undergo the pressure created by the compressor. To provide more convenient operation on top of the structure, a hatch is made. Through it, it is convenient to refuel with a cleaning liquid.