How to build a bath with your own hands

The benefits of baths have been spoken for a long time - it is believed that the human body here undergoes a pair treatment, and not just cleansed, resulting in the body through sweating gets rid of toxins and toxins. In addition, visiting the bath provides good health and significantly increases immunity.

In addition, if the bath is located outside the city, near a lake or forest, it will not only be a means for hardening and washing, but also a great place to relax. And today we want to tell you a little about how to arrange the arrangement of the bath with our own hands, which is very interesting and informative.

Requirements for the furnace

A bath can be considered a bath only when it has a stove. Often the "heart" of the steam room is called a stove-heater. It is needed for intensive warming up of stones, which will subsequently retain heat in your therma. And if you splash a little water on the heated stones, you will get dry steam. Also, such an oven will heat the water that you will use when you visit the bath.

Usually, the ovens in the baths work on coal or firewood, and among the firewood it is best to choose birch, since they are the most caloric by the heat output. Of course, in some cases, making the arrangement of a bath, use ovens on gaseous and liquid fuels. In addition, more and more often started using electric heaters, especially in saunas.

Steam insulation technology

If you want your sauna to be warm, we recommend that you insulate it from the inside. Often, for this in a steam room of wood use a heater (polystyrene foam, mineral wool), paper, polyethylene film or foil.

On the walls of the steam room, a so-called "pie" is usually created. To do this, originally build a wooden crate, after which it nails or a stapler attached foil. This layer will reflect well the heat and create a "thermos effect".

The next layer is to put a film or foil, which will protect the heater from condensation and prevent the appearance of mold. Lay a third layer of paper that will filter the air, then a synthetic heater and a wooden frame.

Warming of the ceiling

If you want to qualitatively make the arrangement of the bath from the inside, we recommend to insulate the ceiling of the steam room from the attic side. To do this, you need to encase the wooden paneling with foil or foil, and then cover the entire area of the ceiling of expanded polystyrene, mineral wool or expanded clay with a thickness of not more than 3 cm. After that, the insulation is covered with a roofing paper or foil.

Making the arrangement of the bath yourself, it is also important to insulate the floor by placing a thermal insulator between the subbase and the finishing floor. Often, for this use polystyrene slabs, which are laid on the waterproofing, covered with reinforcing mesh and poured with concrete.

In a therma for flooring, lattice racks made of wood are used. The floors themselves should have a slight slope so that the water can flow unimpeded to the drain. In the same way make the floors and in the shower.

Installation of electrical wiring

It is very important, making the arrangement of a bath from a tree, it is good to protect electroconducting from heat, steam and moisture. Initially, you need to calculate the power of the current, considering all the lighting devices used. Make sure that the cross-section of the cable used is fully compatible with the power, its insulation is double, and the wires must always be laid in closed boxes.

Features of interior decoration

The arrangement of a bath is impossible without taking into account the purpose of each room, since in most cases it is divided into 4 zones: a rest room, a washing room, a steam room and a dressing room. For decoration of the dressing room use a lining or board, the thickness of which will be about 2 cm. Among the tree, choose cedar, birch, aspen, fir, spruce and pine, as these rocks have a pleasant aroma, do not emit tar and tolerate moisture well.

Materials for the steam room

The best material for finishing this zone is a linden tree, but in some cases it is possible to use boards from another tree. It is important that the evaporation, which is released under the influence of temperature, does not contain a variety of chemical impurities. Therefore, you can not use a tree with antiseptic treatment.

Washing unit construction

About the finished arrangement of the bath can be said when the washing room is completely erected, which can be finished with tiles, natural stone or wood. Consider that the tree should have good moisture-proof qualities, resistance to decay, and the tile can be used any: ceramic, marble or granite. Often in the bath there are metal surfaces and elements that need to be drowned in the tree as much as possible in order to avoid burns.

In a good sauna an important attribute is the pool, which helps to cool off quickly and cool after staying in a good steam room for a long time, which is very useful for health. After a sharp drop in temperature, promoted by chilled water, can be an excellent training for capillaries and vessels. Also, water will close the pores after taking a hot bath.

As you can see, it is rather difficult to make a bath. Photos you can see in our article, and also make your own. But, you see, it's very pleasant to have a rest in the bath-house, where everything is done by oneself!