Screw piles on the fence. Fence installation on screw piles

Each person seeks to protect his house and plot from prying eyes, stray animals and uninvited guests. That's why many build fences. Of course, the hedge must not only protect, but also have an attractive appearance, be reliable and strong enough. In this case, such a fence should be combined with the economy of its erection. What to choose? In this case, a fence on screw piles is perfect . Reviews about such designs are mostly positive. After all, this fence has a number of advantages and minor drawbacks.

Screw piles on the fence

Similar constructions, as can be seen from the name, are mounted using screw piles. They are the basis for the pillars. Also screw piles can be not only the foundation, but also the frame of the whole structure. Such products are hollow metal pipes. At one end of the products there is a special thread and a sharp tip.

It should be noted that the screw piles on the fence are protected from corrosion. In the factory, they are coated with a special coating.

What piles to use for a fence?

Similar products are usually distinguished by several parameters. First of all, the piles are divided according to the types of thread :

1. Standard.
2. With blades.
3. With combined thread.

Screw piles on the fence with different threads differ not only in appearance, but also in those loads that they are able to withstand. The strongest ones are with blades. At the same time such products are of high cost. As a rule, such piles have only two blades. This makes it possible to increase the reliability of such a support, and also to distribute the pressure that appears on it. As a result, the load-bearing capacity of the product is greatly improved. In addition, it becomes possible to apply such piles on virtually any kind of soil.

Also, products are distinguished by their diameter. To install the fence, piles are usually used, in which this indicator is 57, 76 and 89 millimeters. However, the most demanded are the metal products from the pipes. Their diameter is 76 millimeters.

In addition, piles are distinguished by the method of their manufacture: cast, combined and welded. The latter are mainly used to erect fences. Molded structures are optimal for building construction, since they are able to withstand sufficiently large loads. Much less often use combined products, because by characteristics they are very much inferior to the previous ones.

Preparing for installation

Fence installation on screw piles, like any type of construction work, has some nuances that must be taken into account. Before starting the installation, it is necessary to carry out test screwing. This will determine the possible level of penetration of the structure. It should be noted that this indicator directly depends on the composition of the soil. If the soil is very heavy, then the piles can be loaded only 1.5 meters, since screwing in such conditions will be impossible. After that it is necessary to mark out the perimeter. In this case, it is worth remembering the underground communications.

Installation of piles

The distance between the supporting posts should be from two to three meters. Everything depends on the condition of the soil. Optimal is a step of two and a half meters. Once the markup is done, you can start installing the piles. First, you need to make a hole in the ground about 20 centimeters. It is in these places and there will be a twist.

This can be done manually using a lever made of a metal tube. At the same time, the length of it on both sides should be at least two meters. When screwing in, make sure that the pile enters the ground evenly and evenly. To do this, you can use a level or a plumb line. Correct the irregularity will be impossible in the future.

What to do after installing the piles

After all the piles are installed, they must be cut to the desired level, and then filled with a concrete solution. To do this, it is better to use a cement grade not lower than M-150. This will significantly increase the load-bearing capacity of the entire structure, as well as protect it from moisture and its penetration inside the products.

To protect the top of the piles, you need to primed them with a two-component special compound. In addition, it is worth treating the structure with wear-resistant anti-corrosion mastic.

If necessary around the piles, you can make a small groove and fill it with cement mortar.

Next stage

The following actions depend on the pile of what height you need:

1. If the height of the structure is from 1.5 to 2 meters, then it is necessary to install the guiding lag. This is necessary for better fixing the material.
2. If the height is from 30 to 60 centimeters, then installation of fence posts is required.

Fence Installation

When the screw piles on the fence are installed, you can start installing the fence. Usually for these purposes you can use wood, mesh or corrugated board. The hedge made of similar materials looks aesthetically pleasing and meets practically all requirements. Most often use corrugated board. Panels in this case are usually installed parallel to the supporting poles. When attaching the very first sheet, it is important to accurately make all the measurements. Otherwise, when performing further work, there may be distortions.

Also, when installing the very first panel, make sure that the bottom edge remains above the ground at a height of not less than 5 centimeters. Otherwise, the material will not last long under the influence of moisture.

The main stages of hedging

The wooden fence on the screw piles or the hedge from the corrugated board looks original and neat. However, in order to achieve the desired result, it is worth following this sequence:

1. Determine the height from the bottom of the panel of the proflist or the board from the ground.
2. Stretch the construction thread between the posts at a given height. This will greatly facilitate the installation.
3. Attach the first panel, orienting at the same time on the tensioned thread.
4. Lock the hedge material.
5. Align the second sheet.

That's all. Fitting a fence on screw piles is a long process that requires compliance with all rules.