"Interskol" (plane): popular models, instruction, repair, reviews

Electric type benches are excellent for planing planks, as well as bars. The company "Interskol" offers buyers a lot of models that are perfect for both professionals and beginners. When choosing a device, pay attention to the dimensions of the knife, the rated power and the speed of rotation. In terms of dimensions, the planes are quite different.

Some models have a separate branch pipe for chips. The frame for the tool is usually made with a lining. Some modifications use an adjusting starter. For professionals, such devices are great. The average model is about 8 thousand rubles.

Instructions for using the tool

Before using the instrument, it must be adjusted. For this, a knife is placed, which is located in the lower part of the structure. The height of the plate is regulated by the pivoting mechanism. The chip socket must be open. Before connecting the instrument to a 220 V network, it is important to make sure that the start button is not turned on. After connecting the model, the power is set. If necessary, the height of the plate can be adjusted.

Repair model

Most often, the rotor breaks the planes. The element is located near the motor. In order to repair the tool yourself, you have to use the key. First, the protective cover is removed from the underside of the housing. After that, the starter is removed directly. The next step is to twist the lining. Behind it is a rotor, which is attached to the screws.

After detaching the part, it is checked for defects. If the device is blown, black marks will be visible on it. In this situation, the model can not be repaired. Also, the problem may be the failure of the capacitor, which is located inside the rotor. Its performance is verified using a tester. If the threshold resistance is below 30 ohms, the rotor should be completely replaced.

Description of the plane "Interskol R-110"

The indicated planes (electric) "Interskol" reviews tend to get good. The power of the tool is 3.5 kW. If you believe the feedback of experts, then for the jointing of boards the model fits perfectly. The holder in the device is used with a lock. If necessary, it can be adjusted in height. The plate near the model is located under the motor.

According to the owners, the rotor breaks very rarely. System protection from dust and moisture in the device is. For the treatment of pine boards the model is suitable. The knife is set to a width of 4.7 cm. The adjustment of the plane "Interskol" does not take much time. The reducer is of the collector type. In the standard toolkit there is a ruler and a key. If you believe the reviews, the bottom cover is removed without problems. Buy the specified instrument on the market can be priced from 7800 rubles.

Reviews of the model "Interskol P-102"

Reviews of the planes "Interskol R-102" can be found very diverse. For professional use, they are not suitable. The motor in this case is of low power, and the maximum frequency is 1500 rpm. For the treatment of pine boards the model is used often. The rack is not very wide, and the modification weighs a bit. The width of the knife is 5.2 cm. The holder is not in this case.

The system of protection against moisture in the tool is not provided. If you believe the feedback of buyers, then the problems with overheating of the engine are observed infrequently. The plate in this case is easily adjustable. The handle is used with a polymer lining and does not slip in the hand. The tool frame is made of stainless steel. For the treatment of pine bars model is suitable. Of the disadvantages, it is important to mention the high noise parameter. At maximum speed, the model produces as much as 77 dB. Buy the specified manual plane "Interskol" can be priced from 7 thousand rubles.

Parameters of the plane "Interskol R-105"

Rubber "Interskol P-105" has a lot of advantages. Specialists praise him for the quality knife. The plate in the standard set includes an adjustment type. The controller of the tool is installed in the front of the structure. According to buyers, knives can be adjusted very quickly. The mains cable is used without the holder. In the kit, a compact key is attached to the plane. You can unscrew the bottom cover of the tool without problems.

A dust protection system is available. The branch pipe in this case is near the bottom of the plane. The permissible operating temperature is a maximum of 45 degrees. The width of the knife is 5.4 cm. The starter at the planer is used with the controller. The instruction of the plane "Interskol R-105" in the set is. The reducer is used with a through capacitor. The system has no moisture protection. Buy a plane in this series, the user is able to price from 6700 rubles.

Description of the plane "Interskol R-82TS-01"

The planer of this series is ideal for repair work in the house. Among the features of the modification, it is important to mention a quality pen. The lining in this case is made of polymer. If you believe the feedback of experts, the motor of the model is of high quality. For the processing of maple boards the model is suitable. The holder in this case is made of plastic.

The width of the knife is 4.6 cm. If necessary, the user can adjust the slope of the plate. The power cord has a length of 1.2 m and does not interfere during planing. The stand is made entirely of stainless steel. The controller is used with the starter. Buy a plane nowadays you can price from 7900 rubles.

Reviews of the model "Interskol P-55"

Rubanok of this series of reviews is mainly of a positive nature. For professionals, the model fits perfectly. The power cord in the device is used with the holder. According to buyers, the plate is regulated without problems. If necessary, it can always be cleaned. A dust protection system is not provided. The power of the motor is equal to as much as 4.6 kW. The frequency at this maximum reaches 2300 rpm.

The reducer in the tool is used with the controller. The speed regulator is located at the front of the structure. The instrument has a moisture protection system. The starter is of the wired type. The width of the knife is 4.7 cm. The angle of inclination of the plate can be adjusted without problems. The permissible operating temperature is 40 degrees. The key for removing the plate in the standard set is. Disassemble planes "Interskol" can quickly. The rotor is used with a lid. Buy a plane of this series can be priced from 7800 rub.

Parameters of the plane "Interskol R-82TS-05"

Another model of the trademark "Interskol" - the plane P-82TS-05 - is produced with a capacity of 4.3 kW. The frequency thus reaches a maximum of 1400 rpm. The reducer of the model is used with the controller. If you believe the opinions of specialists, then it rarely breaks. It is also important to note that the model uses a system to protect against plate overheating. For the processing of maple boards, the plane is suitable.

The system of protection against moisture is applied to the third degree. The starter in the device is of high quality. The width of the knife is 4.3 cm. The slope of the plate in this case is not adjustable. The start system is provided with a rotor. Buy this plane in a specialized store can be for 6300 rubles.

Reviews of the model "Interskol P-66"

What other models does the company "Interskol" produce? The R-66 has a lot of advantages. Among them, it is important to note the compact size. The handle on the model is made with high-quality polymer lining. The stand is made of stainless steel. There is no smooth start system at the planer. To model the bars, the model fits perfectly. The dust protection system in the device is used in the third class. According to experts, the rotor of the model is used with a pass-through capacitor.

It is cooled very quickly, therefore it is allowed to use this tool for a long time. Among the shortcomings, it should be noted a high energy consumption parameter. The system of protection from moisture at the plane is absent. The rotor is used without the controller. The width of the knife is only 4.2 cm. There is no possibility to adjust the slope of the plate. Buy a plane in this series, the user is able to price from 6 thousand rubles.

Parameters of the plane "Interskol R-80"

What else can the brand "Interskol" offer to its customers? Rubber R-80 is most suitable for processing bars. The controller is used with the controller. In this case, the protective plate is made of stainless steel. The handle is applied with a polymer lining. According to buyers, the condenser rarely overheats. The moisture protection system is used in the second class. Speaking about the parameters, it is important to note that the power of the plane is 3.6 kW.

The maximum frequency is 1800 revolutions per minute. For the treatment of oak boards the model suits perfectly. The dust protection system is used rather high-quality. The stand is made of plastic. The rotor of the model is at the rear of the structure. The model weighs only 3.2 kg. In the standard set of planes, there is a key for removing the plate. The tool knife is quite easy to replace.

In case of a motor failure, repair of the Interskol plane is best done at the service center. Of the drawbacks, it is important to note the absence of a plate tilt adjuster. The noise level is 79 dB. Protection from overload of voltage at the plane is absent. Buy a tool of this series, the user is able to price from 6 thousand rubles.

Description of the model P-23 of the firm "Interskol"

Rubber R-23 is well suited for processing pine bars. Also, the model is able to perfectly handle oak boards of various sizes. The reducer for the model is of contact type. The controller is located in front of the frame. There is no stand in this case. If you believe the opinions of experts, the plate is regulated very simply. The width of the knife is 5.3 cm. The tilt angle of the plate is adjustable. The power cord is used with the holder. In the standard set of planes there is a key.

The moisture protection system is used in the third class. The handle at the tool is provided with a polymeric overlay. The start system is of high quality. However, it is important to note that the plate height adjuster is not available. For the processing of cedar products, the model is not suitable.

The noise level of the plane is 67 dB. Repair of the plane "Interskol" is more expedient to carry out in the service center. The manufacturer does not provide a dust protection system. Buy the plane presented by the series user can price from 7500 rub.

Description of the plane "Interskol R-86TS"

It is a compact and inexpensive plane. The power of the tool is 4 kW. The system has no moisture protection. If you believe the reviews, the rotor is used with a quality controller. The power regulator is located in the front part of the base. The network cable is equipped with a holder. The width of the knife is only 4.3 cm. If you believe the experts, the plate is regulated without problems. Buy a model in our time, you can only for 5700 rubles.