How to make a receiver for the compressor with your own hands

Compressor plants are capable of operating only from receivers. These devices are responsible for the pressure inside the system. Many modifications are made with relays, which differ in the clamping force. Also it should be noted that the receivers can be equipped with sensors. Filters are most often used with clamps. If necessary, the receiver for the compressor can be made independently. However, it is important to consider the type and power of the compressor unit.

40 Liter Devices

Make a receiver for the compressor with your own hands for 40 liters is quite simple. First of all, the camera is being prepared for the device. As a rule, a sheet of stainless steel is used. Experts say that the lid should be welded in the last place. It should also be noted that there are two-chamber modifications. The simplest relay is to use low conductivity. Homemade modifications, as a rule, are not equipped with sensors. Reducers for devices are selected in a chain type. In this case, valves with a tee are used for blowing air.

Modifications to 60 liters

An additional receiver for a 60 liter compressor can be made with two cameras. Experts say that a sheet of metal should be a thickness of 1.3 mm. Tees are most often installed next to the relay. Receivers of this type must be equipped with two filters. The reducer should be installed with an adapter. Modifications of 60 liters are great for compressors of low power. The maximum pressure limit for the systems is 6 bar. It is also important to note that when assembling, only a channel valve should be used.

80 liter unit

Air receivers for a compressor of 80 liters are allowed to be manufactured for two relays. Experts say that the filters are selected with a large diameter. The outlet pipe at the receiver should be at the top. Intermediate filters are mounted through an adapter. Also it should be noted that the modifications with stops that are inside the camera are considered common. The pressure parameter for the receivers of this type is approximately 10 bar. Relays they use a wired type. The compression force is a maximum of 3 N. The tees under the modification are selected with a diameter of 2.2 cm. It should also be noted that sensors are often installed in the devices for monitoring the pressure level.

Models with one valve

How to make a receiver for a compressor with one valve? Shells in this case are used for 30 liters. You can also consider more compact modifications. To build the receiver, the camera is first prepared. The hole for the reducer is welded small diameter. Specialists recommend using only a wire relay with a tee. The diameter of the outlet branch pipe for modification of 30 liters should not exceed 2 cm. The reverse action valve is mounted at the base of the filter. It should also be noted that modifications are considered common for two outputs. They are great for compressors with 10 kW. The pressure in the system can be maintained at 5 bar.

Device for two valves

The receiver for the compressor on two valves is assembled with a capacity of 40 liters. On average, the pressure of the models of this type is at the level of 4 bar. Devices primarily differ in the conductivity of the relay. The clamping force at them is a maximum of 7 N. Many modifications are made with a contact reducer on two outputs. If you collect a simple modification, then the tee is more appropriate to use without a sensor. It is also important to note that the check valve should always be installed behind the filter. Experts say that the outlet pipe is welded in the last place.

Single-chamber devices

Single chamber version is suitable for compressor installations of different capacities. Devices of this type are actively used in large plants. Modern models are distinguished by a high pressure parameter. They use a safety valve and a protected gearbox. To independently assemble a single-chamber receiver, it is recommended to make a container for it. The relay is used with a conductivity of 1.2 microns. The clamping force must be a maximum of 12 N.

Valves of the reverse type are mounted behind the filter. The reducer must be located in the rear part of the container. The optimal diameter of the outlet branch pipe is 2.2 cm. However, it is important to consider the volume of the chamber. If you assemble the device by 40 liters, then the intermediate filter is installed behind the relay. Also it should be noted that before using the equipment, the camera should be checked for sealing.

Two-chamber modifications

Two-chamber homemade receiver for the compressor is produced with a tank of 60 liters. Some devices are made with a sensor. For self-assembly of the model you will need to make a camera, and also make a hole for the branch pipe. The relay is normally wired. Adapters are more suitable to use with wraps. Experts say that the receiver must withstand high pressure. The optimal diameter of the outlet branch pipe is 2.2 cm. The valves for the devices are selected from steel or aluminum alloy.

Using gearboxes with blockers

The receiver for the compressor with the blockers is problematic to assemble. First of all, it is important to note that models must have a high parameter of permissible pressure. Filters for devices are suitable only on the lining. It should also be noted that the relay must be installed before the gearbox. Experts say that receivers of this type are manufactured with small tees. Some modifications are collected with carry. Sensors are used to normalize the pressure inside the chamber. The reverse action valves are installed with partitions. They are able to pass air in only one direction.

Devices with pressure sensors

The receiver for the compressor is produced with cylinders of different capacities. Some devices are suitable for powerful compressor installations. However, in this case, much depends on the diameter of the branch pipe. If we consider the models for one output, then they have an acceptable pressure rating of 5 bar on the average. In this case, the clamping force can reach a maximum of 12 N.

Reverse valves are installed with and without linings. Reducers can be found in different conductivities. Tees on receivers are installed with a diameter of 2.4 cm. If we consider simple modifications, then they use only one filter. The admissible pressure indicator for this type of receivers is about 2 bar. They are suitable for compressors with a total power of 8 kW.