How does a motoblock sink? How to plow a plow on a motoblock correctly?

Motoblock is the most popular technical tool that is used by summer residents on private farms for soil cultivation. This was facilitated by the simple arrangement of such units, and the relatively high quality of the ground treatment. However, to get a decent result in the course of the work, you need to know how to plow a motoblock and how to handle it properly. The ability to complement the design of auxiliary attachments also extends the functionality of the models, while forcing users to study in detail the rules of operation in special modes.

How does a motoblock plow?

In the process of cultivation of the soil, special cutters are involved-the working organs that directly effect loosening. Another important element is the opener, which allows you to adjust the depth of processing. As a rule, the opener limit reaches 25 cm. Understanding how a tiller plows, it will be possible to optimally adjust the level at which the cultivation of the earth will be performed. Rotating knives are driven by a drive mechanism, which can be different - with a diesel engine, gasoline or even electric. Such a system can be called automatic, but considerable responsibility for the quality of work is assigned to the user who not only makes the initial settings of mechanisms and regulates the parameters of plowing, but also controls the motor block in the course of loosening.

Launching the motoblock

Before starting to work on the ground, it is necessary to engage the clutch, put the gearbox on the "neutral", start the engine and give it a little warm up. The answer to the question of how to plow a motor-block almost always involves recommendations for setting the optimum speed at which the drive will operate the knives. This parameter will determine the nature of the tillage. Normal rate for cultivation is the second - it is recommended to perform medium-quality soil cultivation. The speed can vary during operation, but it should be controlled by changing the parameters of the belt drive. Correction usually occurs when the depth of treatment changes or as a result of the transfer of machinery to a different type of soil.

Configuring Processing Parameters

If it is supposed to process virgin soil, it is desirable to set a small depth and to feel how much the unit is able to cope with such soil. After processing a small segment of the site, you should determine the "convenient" depth. Knowing how to plow a motoblock ground with a specific density and composition, will help to establish the optimal position of the cutters and adjust the opener accordingly. No less important is the width of the loosening, which should be adjusted by installing several rotating knives or rotors. Their number in standard operating modes can vary from 2 to 6. It happens that the engine of the unit starts to increase the speed while reducing the depth at which processing is performed. In this case, it is necessary to independently open the opener.

Working with the plow

The presence of the plow in the construction of the motor block significantly expands its capabilities. To understand how to plow a plow on a motor block, you must first familiarize yourself with the procedure for assembling it, which involves the installation of a coupling mechanism on this element.

Coupling with the plow in the future will make it possible to connect the elements with the motor block. To perform this operation, appropriate spanners and fasteners are required. At the same stage it is necessary to determine and fix the depth of processing. This is done by comparing the hub holes on the hitch with one of the holes on the plow stand - fastening is done by bolt and nut. Next, you can check how the plow motoblock plows on malleable soil and, if the mechanisms demonstrate a good work, you can start full cultivation on the site.

The process of processing the land

Having convinced that all working elements are reliably fixed, it is possible to begin plowing. Despite the fact that the main time processing of the land will be carried out in the second gear, it is important to know and how to plow the motoblock in the first gear. For this, the clutch is gently squeezed out and the optimum position of the device is established. In this mode, work is carried out with the first groove. Based on the results of the "test" cultivation, it is possible to draw conclusions about the need for adjustments.

If the unit has stopped moving forward, and the cutters are buried, it is necessary to raise it by the handles and force it to a level position. Often there are deviations in the sides - these are the leads that usually occur on furrows that have already undergone cultivation. From here there can be other question - how correctly to plow motoblokom that rotating knives did not leave in the ground? Help in this can only be appropriate manipulation of the handles. Unfortunately, careful monitoring should be on any soil. So, on loose ground it is necessary to make sure that the cutters do not sink too deeply, and in the process of processing hard soil and virgin soil, there may be a need for several approaches. It is desirable to perform the first treatment at low speed, and it is important to adjust the opener position accordingly.

Safety precautions

Quite a few questions as to how to properly plow a motoblock help to solve the knowledge of the design of a particular model of the unit. Also it is necessary to take into account the safety techniques, as the motor block is a technical tool, the work of which is connected with the rotation of sharp elements - rotors, mills, knives, etc.

First, you need to make sure that there are no children or animals in the area to be treated. Further, all fixing components are checked - especially on mills and rotors. If the model is equipped with high-voltage wires and an exhaust pipe, then it is impossible to touch them during operation. Also, plowing the garden with a motor-block is recommended in the appropriate outfit. In particular, it is necessary to have strong outerwear, shoes with a solid sole and gloves. When working on rough terrain and soils with stony ground, special care should be exercised during reverse movement. Due to the unevenness of the treated area, the risk of slipping or stumbling is greatly increased.