Types and dimensions of drills for concrete for perforator

It is not necessary to doubt the indisputable merits of a puncher, if necessary, the arrangement of openings, niches and openings in concrete structures. Whereas the speed of work and the quality will depend on the size of the drills for concrete for the perforator have been chosen. Important and a variety of this element.

Difference of drill from drill

The puncher has long been the most suitable tool in those cases where it is necessary to combine drilling with the chiselling function. A significant difference between a perforator and an ordinary drill is the presence of a lock-cartridge, in which removable attachments are fixed. As the latter can act all sorts of tips that can look like blades, drills and bits. The dimensions of the drills for concrete when selecting should also be taken into account. At first glance, the drill used in perforators is no different from the traditional winning drill, which is used when working with a drill. However, there are differences, and they are very significant. The shank of the drill is smooth, while this part of the drill has a complex shape.

What is important to pay attention to when choosing

The grooves, which are twisted in a spiral, are sharp enough to be cut into the material, but the same grooves of the drills are intended for the extraction of dust and chips that occur when working with a tool. Some products intended for punchers may even have triple spirals. The dimensions of the drills for concrete for a perforator must be chosen by you depending on the purpose.

As a common distinctive feature in these cases is the winning tip, thanks to which it is possible to drill and chisel hard materials by the type of concrete. If you have a three-mode punch, then with it you can work as a conventional drill. This allows you to use conventional drills with this tool. However, for this it will be necessary to use an adapter, which often comes complete with a perforator.

Recommendation of the master

You can use the opposite method, which presupposes the possibility of installing a drill into a drill, which can work in impact mode. However, this performance and high efficiency will not be achieved. In addition, if the element is in the cartridge, and it can not be extracted on its own, you will also have to repair the drill.

The solution of complex problems

Complex tasks, which are designed to perform a puncher, could not remain without improved solutions. There are several types of quick-clamping cartridges, each of which is designed for its own shape of the shank-nozzle. Each variety, in turn, should be used at different loads. The most common are two types: plus and max. At the same time, a uniform standard is used for all - SDS, which provides for the possibility of fixing the nozzle with one hand movement. However, a pure variety is used quite rarely, most often you can find an intermediate version - SDS-top. Determine the necessary variety of nozzle help instructions to the puncher, in it you can find information about which one is suitable for a particular model. This factor will play a huge role when buying a puncher, because if you become an owner of a tool with a rare variety of consumables, you will be tied to a specialized store that sells machinery, which is not convenient. A set of Boers for each class of its own. All models can be divided into heavy, medium and light. The first are jackhammers, nozzles for them are required corresponding.

Expert opinion

If you have a middle or light class perforator, then the drill for it should be used with the shank plus, as for the max shanks, they are suitable for heavy-duty attachments. Modern manufacturers are trying to produce a variety of adapters, allowing you to install drills of one class in the cartridge of another, but experts do not recommend doing this, since each model of the perforator is designed for attachments of a certain size and weight. If a heavy punch from consumables of a certain type does not suffer, then the medium and light will fail in a short time, repair of equipment will cost more.

Popular bore sizes

The most popular today are the borax, which resembles a drill in shape . The spiral cutting part, as in the case of a drill, automatically removes the destroyed material elements from the internal space of the hole. When choosing a drill for concrete perforator (dimensions 32), you can see that the cutting edge is made on the basis of carbide materials, this part has a rounded shape. Due to this factor, the nozzle has the ability to undergo shock loads. Choosing attachments for professional work, you should pay attention to tools that have a centering spike, as well as self-sharpening forms of working faces. If you decide to purchase a drill for concrete perforator (size 26), you should know that it is not subject to sharpening, as well as repair and leveling. During operation it needs to be cooled and washed, this element is a consumable device that must be carefully stored. The most common drill bit size for a perforator is a parameter equal to 6 millimeters. Drills are sold in packages, the number of elements in which can be limited to ten pieces. Choosing these accessories, you need to pay special attention to the spiral. The more twisted it is, the better it will be to ensure the removal of waste material, the faster and better the drilling will be. However, the strength characteristics are higher for those Boers that have less twisted spirals. The drill for concrete perforator (dimensions 6) is the most common. In SDS-plus nozzles, the shank diameter can not exceed 10 millimeters, whereas this parameter, characteristic of the drill itself, can vary from 4 to 26 millimeters. The length of the product can vary from 100 millimeters to 100 centimeters. The master must take into account the total length along with the shank. If you are considering drills for a perforator for concrete, the recommendations of a specialist should help you purchase a quality product. Nozzles designed for heavy-type perforators in the shank can reach a diameter of 18 millimeters. The diameter of the drill itself can vary from 20 to 80 millimeters. The spiral on this nozzle has a shape that removes the slag and cools the surface from which it comes into contact. Such attachments are used in the role of breakthroughs, with their help you can destroy the wall to arrange the doorway. On sale it is possible to find also nozzles by type of crowns which are used for making holes for switches and sockets. If you are looking for a drill for concrete puncher (diameter 65 mm), you will be able to additionally purchase entire systems that are designed for particularly difficult cases. In this example, we are talking about chiselling reinforced walls of impressive thickness.

The main varieties of borax

Once you have learned what the size of the drill bit for concrete is for a perforator, it is important to familiarize yourself with the main varieties of these components for your tool. Thus, for the implementation of specific manipulations, a drill bit should be used. It is used when laying on the concrete walls of electrical wiring. With its help it is possible to make a hole of any diameters for the installation of switches, junction boxes, and also sockets. Among the varieties, we can distinguish a flat chisel, which drills concrete more precisely; And a chisel made in the form of a peak. Using it, you can destroy concrete. Another type is a channel drill that facilitates the laying of an electrical wire.

Varieties of Boers by manufacturers

Different sizes of drills for concrete for a perforator can be chosen by you in the stores of the corresponding goods, but it is important to pay attention not only to the parameters, but also to the manufacturing company. Today, only 14 plants are officially engaged in the production of these products. This indicates that the variety of attachments can be divided into two categories, one of which is official, while the other is not original. In the latter case it is difficult to talk about quality, as the product does not have a certificate. With original drills, too, it is worth investigating, as the DreBo Werkzengfabrik plant produces products not only under its own brand, but also for Wurth, Milwaukee, and Hitachi. Therefore, in this case, you need to be guided by additional parameters, as well as form. The quality of the products will not differ.

Conclusion

If you decide to purchase a drill for a perforator for concrete (size 50), then you can use it to carry out a wide range of works. However, you should not choose products that were produced by companies that did not confirm their reputation in the market of the corresponding goods.