Pulling up an office chair with your own hands: features, instructions and recommendations

To pull the chair can be any material, depending on the taste preferences of the client, interior solution or financial possibilities. This can be the skin, its substitute or other textile analogue.

Constriction components

Pulling an office chair with your own hands often occurs with the following types of materials:

- Genuine Leather. It is considered the most elite and prestigious option. Work with him should be neat. The work will require additional tools that will also increase the cost of repairs.

- Leather imitation leather. The most optimal option for the price category, but also the most short-lived. This constriction office chair, although cheap, but will serve this material no more than 2 years, which is less than inexpensive fabric upholstery. There are leatherette of high quality, which is not inferior to natural leather, but their cost is almost equal.

- Textiles. This material has the widest assortment both in color scale, and in a fabric texture. The cheapest option is Chenille - a fabric made up of cotton and synthetic fibers. Next in increasing prices: flock, jacquard, microfiber and tapestry.

Features of repair

The design of the chair and its material are determined by what it is intended for. It can be a chair of the chief or managerial staff or an ordinary employee or client. On the status of the chair says its upholstery. Often this is a leather option. Others have cheaper analogs or a textile surface - they are lighter in design and mobile. When the chair is very fond of the owner, it is not necessary to buy a new one and get used to it. You can order the upholstery of old furniture or do it yourself, if skills, materials and tools allow.

Stages of work

Pulling up the upholstery of an office chair with your own hands is not such a difficult task as it may seem at first. It is not necessary to call a wizard if you have the tools and materials at hand. To work, you need the following items: fabric for sheathing, foam rubber, scissors or knife, screwdrivers - cross and flat, a furniture stapler.

Before starting work, the chair is to be dismantled. It is easier to do this if there is an instruction. But often there is none, so you need to understand the device and properly disconnect the cover and seat. It is better to take a picture of the chair before the beginning of the analysis and on the next stages, because it will be easier to collect it after the repair. A simple product has a standard fasteners, so the tightening of the office chair by your own hands will not take much time. It is enough to unscrew the bolts and screws in certain places. When parts of the chair are dismantled, you can proceed to remove the old upholstery. For this, pliers, a screwdriver and an anti-stapler are used, if there are staples. After that, by the standards of the old plating, we make patterns on the new material. To do this, simply attach the products to each other and circle the contour.

Next, the material should be laid on the floor in this order: the lining component, the foam rubber and the frame (backrest or seat). Then firmly fix the first to the frame, while it is good to pull it - do not fold, and carefully fix the result with a stapler. Pulling an office chair with leather is not only giving an updated kind of furniture, but also raising the status of the organization, especially in the eyes of customers. When both parts are trimmed, you can assemble the chair back and enjoy the work done.

How to draw a chair Alcantara?

Such material as Alcantara is widely used in various fields. This is an artificial suede, which has a sticky layer underneath. Due to this, it ideally falls on the surface. Alcantara has a good service life (up to 7 years), it is not very stretchy, but flexible enough to create convenience for work. The best alcantara is produced in Korea, it must have a drawn mesh 5 x 5 cm on the back side. To pull the chair of Chinese production can be using the following devices: pliers, marker, tape centimeter, scissors, ruler, knife, directly alcantara with self-adhesive.

To prevent over-expenditure of material, it is necessary to make a calculation. To do this, measure all parts of the chair. Then add 5 cm to each side to the allowances. The surplus will then be cut off with a clerical knife. After that, you can disassemble the chair by simply unscrewing the necessary elements. Further cut off the necessary pieces of Alcantara, noting the size of the marker on the inside.

Should I remove the old upholstery?

Pulling an office chair Alcantara involves the possibility not to remove the old upholstery. Alcantara is so comfortable material that it falls on any surface. From the piece, you need to separate the protective backing and attach it to the workpiece, while you need to straighten the alcantara so that there are no folds. Surplus wrap around the edges. Later they are fixed or cut off. At the same time it is necessary to cut off immediately, otherwise it will be impossible to mold the alcantara after an hour.

Constriction of the whole chair or part?

Often, users are unhappy with only a part of the chair, while you can replace the shell only the backrest or seat. The scope of work must be established before they begin. Pulling an office chair is not necessarily accompanied by an appeal to specialists. You can use the repair tips, equip yourself with the necessary tools and materials and make an independent restoration.

Office chair repair

Often organizations give chairs for repairs. Overstretching of office chairs is a simple task, but when the amount of work is large, only professionals can deal with it quickly and qualitatively. They can arrive at the office or home, free to measure and calculate the exact cost of the work. Also pick up the items for repairs and bring them back at the set time. Often, the whole work takes no more than 2-3 days. Not only the replacement of the upholstery is included in the work of such firms. They can repair the frame of the chair itself, replace the rollers and legs, foam rubber and plywood. The cost of the service will depend on the volume and urgency of the work performed. The calculation is based on what parts were used, what time was spent.

Price

Pulling up office furniture is a job for a number of professionals. Now the market abounds with firms that provide similar services. Often they offer the following service:

- departure of gauges to the site and drawing up work estimates;

- transportation of the chair;

- dismantling of the product;

- Preparation of upholstery material for sketches;

- directly peretyazhk office chair;

- return of the finished product at the expense of the company.

Each organization has its own price list for the services provided, and prices vary from 500 rubles and higher. It matters not only the material, but also the design of the chair, its dimensions and initial cost. Overstretching of an office chair, the price of which depends not only on the cost of the firm's services, but also on the material of the cladding chosen by the customer, will allow returning the old kind of old furniture. As a rule, the catalog is provided by the company itself, it includes both natural leather and its substitutes, as well as textile analogues.